Bosch PHG 500-2 Instructions D'emploi page 13

Soft Soldering
G
For point soldering, place on the reduction nozzle 11,
for the soldering of pipes, the reflector nozzle 8.
If solder without flux is used, apply soldering grease or
paste to the location to be soldered. Warm the loca-
tion to be soldered for 50–120 s depending on the
material. Apply the solder. The solder must melt from
the work piece temperature. After the soldered loca-
tion has cooled, remove the flux.
Maintenance and Cleaning
Before any work on the unit itself, pull the mains
s
plug.
For safe and efficient working, always keep the unit
s
and the ventilation slots clean.
WARNING
Important instructions for connecting a new 3-
pin plug to the 2-wire cable.
The wires in the cable are coloured according to the
following code:
Strain relief
Live = brown
Neutral = blue
Do not connect the blue or brown wire to the earth ter-
minal of the plug.
Important: If the plug on the cable of this unit must
be replaced, dispose of the old plug to prevent mis-
use.
If the unit should fail despite the care taken in manu-
facture and testing, repair should be carried out by an
authorised customer services agent for Bosch power
tools.
For all correspondence and spare parts orders, always
include the 10-digit order number of the unit.
Environmental Protection
Recycle raw materials instead of
disposing as waste.
The unit, accessories and packaging
should be submitted for environment-
friendly recycling.
These instructions are printed on recycled paper man-
ufactured without chlorine.
The plastic components are labelled for categorised
recycling.
1 609 929 E16 • (03.05) T
Service and Customer Advice
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham-Uxbridge
Middlesex UB 9 5HJ
✆
✆
Fax . . . . . . . . . . . . . . . . . . . +44 (0) 18 95/83 87 89
Ireland
Beaver Distribution Ltd.
Greenhills Road
Tallaght-Dublin 24
✆
Fax . . . . . . . . . . . . . . . . . . . . . + 353 (0)1/459 8030
Australia
Robert Bosch Australia L.t.d.
RBAU/SBT2
1555 Centre Road
P.O. Box 66 Clayton
3168 Clayton/Victoria
✆
Fax . . . . . . . . . . . . . . . . . . . . +61 (0)1/800 819 520
To be fitted
www.bosch.com.au
by qualified
E-Mail: CustomerSupportSPT@au.bosch.com
professionals only
New Zealand
Robert Bosch Limited
14-16 Constellation Drive
Mairangi Bay
Auckland
New Zealand
✆
Fax . . . . . . . . . . . . . . . . . . . . . . +64 (0)9/47 82 914
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents:
EN 60 335 according to the provisions of the direc-
tives 73/23/EEC, 89/336/EEC.
Dr. Egbert Schneider
Senior Vice President
Engineering
Robert Bosch GmbH, Geschäftsbereich Elektrowerkzeuge
Specification subject to alteration without notice
English–4
Service . . . . . . . . . . . . . . +44 (0) 18 95/83 87 82
Advice line. . . . . . . . . . . . +44 (0) 18 95/83 87 91
Service . . . . . . . . . . . . . . . . + 353 (0)1/414 9400
. . . . . . . . . . . . . . . . . . . . . +61 (0)1/800 804 777
. . . . . . . . . . . . . . . . . . . . . . . +64 (0)9/47 86 158
Declaration of Conformity
03
Dr. Eckerhard Strötgen
Head of Product
Certification