Ryobi LCS-180 Mode D'emploi page 7

GB
FR DE ES IT
SPECIFIC SAFETY RULES
Q
Lower guard may be retracted manually only
for special cuts, such as "plunge cuts" and
"compound cuts." Raise lower guard by retracting
handle. As soon as blade enters the material,
the lower guard must be released. For all other
sawing, the lower guard should operate automatically.
NOTE: Alternate wording may be substituted for
"retracting handle."
Q
Always observe that the lower guard is covering
the blade before placing saw down on bench or
floor. An unprotected, coasting blade will cause the
saw to walk backwards, cutting whatever is in its
path. Be aware of the time it takes for the blade to
stop after switch is released.
ADDITIONAL SAFETY RULES
Q
Check damaged parts. Before further use of
the tool, a guard or other part that is damaged
should be carefully checked to determine that
it will operate properly and perform its intended
function. Check for alignment of moving parts,
binding of moving parts, breakage of parts,
mounting, and any other conditions that may
affect its operation. A guard or other part that is
damaged should be properly repaired or replaced
by an authorized service center. Following this rule
will reduce the risk of shock, fire, or serious injury.
Q
Inspect for and remove all nails from lumber
before using this tool. Following this rule will reduce
the risk of serious personal injury.
Q
Do not operate tool while under the influence
of drugs, alcohol, or any medication. Following
this rule will reduce the risk of electric shock, fire,
or serious personal injury.
Q
Do not place battery tools or their batteries near
fire or heat. This will reduce the risk of explosion and
possibly injury.
Q
Batteries vent hydrogen gas and can explode
in the presence of a source of ignition, such as
a pilot light. To reduce the risk of serious personal
injury, never use any cordless product in the presence
of open flame. An exploded battery can propel
debris and chemicals. If exposed, flush with water
immediately.
Q
Do not charge battery tool in a damp or wet
location. Following this rule will reduce the risk of
electric shock.
Q
For best results, your battery tool should be
charged in a location where the temperature is
more than 10°C but less than 38°C. Do not store
outside or in vehicles.
961075070-03_LCS180_EU.indd Sec1:2 961075070-03_LCS180_EU.indd Sec1:2
NL PT DK SE FI NO
English
RU PL CZ HU RO LV
Q
Under extreme usage or temperature conditions,
battery leakage may occur. If liquid comes in
contact with your skin, wash immediately with
soap and water, then neutralize with lemon juice
or vinegar. If liquid gets into your eyes, flush them
with clean water for at least 10 minutes, then seek
immediate medical attention. Following this rule will
reduce the risk of serious personal injury.
SPECIFICATIONS
Motor
Blade Diameter
Blade Arbor
Cutting Depth at 0º
Cutting Depth at 45º
No Load Speed
MODEL BATTERY PACK
(not included)
BPP-1815
BPP-1815M
BPP-1817
BPP-1817M
BPL-1820
LCS-180 BPL-1815
BPP-1815
BPP-1815M
BPP-1817
BPP-1817M
DESCRIPTION
1. Lock-off Button
2. Switch Trigger
3. Dust Pipe Joint
4. Depth Adjustment Knob
5. Width of Cut Scale
6. Bevel Adjustment Knob
7. Spindle Lock Button
8. Lower Blade Guard
9. Blade
10. Blade Screw
11. Outer Blade Washer
12. Inner Blade Washer
13. To Loosen
14. To Tighten
15. Battery Pack(Not included)
16. Depress Latches to Remove Battery Pack
17. Guideline
18. Blade Guide Notch
2
LT EE HR SI SK GR
18 Volt
150 mm
10 mm
45 mm
32 mm
4,200 min -
1
CHARGER
(not included)
BCL-1800
BCS618
BCL1418
BC-1815S
BC-1800
1/5/10 10:46:28 AM 1/5/10 10:46:28 AM
TR