Fader Start Function; Using External Effectors - Pioneer DJM-1000 Mode D'emploi

OPERATIONS

FADER START FUNCTION

By using a control cable to connect the unit to an optional
PIONEER CD player, playback on the CD player can be
started using the channel fader or cross fader functions (if a
digital link connection is made, use of the control cable is
unnecessary).
The CD player's pause function is canceled when the
mixer's channel fader slider or cross fader slider is moved,
and the playback of the track starts automatically and
instantly. In addition, by returning the fader to it's former
position, the CD player's playback can be returned back to
the cue point (back cue), so that sampler-like playback can
be performed.
[Cross fader start play & back cue play]
During cue point standby on the CD player assigned to
channel A of the cross fader, moving the cross fader slider
from the right side (B side) to the left side (A side) causes
the CD player connected to channel A to start playback.
When the cross fader slider reaches the left side (A side),
the CD player assigned to channel B will back cue (return to
cue point). When the CD player assigned to channel B is in
cue point standby mode, moving the cross fader slider
from the left side (A side) to the right side (B side), causes
playback on the CD player assigned to channel B to begin.
When the cross fader slider reaches the right side (B side),
the CD player assigned to channel A will back cue.
* Back cue will occur even if the input selector switch is
not set to [CD/LINE].
External effector
[Starting playback with channel fader]
1 Press the FADER START button for the channel (CH-1 to
CH-6) connected to the CD player you wish to control.
÷ The button of the selected channel will light.
2 Move the channel fader slider to the [0] position.
3 Set a cue point in the CD player, and set to standby at
cue point.
÷ If a cue point has already been set, the CD player does
not have to be set to standby at the cue point.
4 Move channel fader slider at the desired timing to start
playback.
÷ CD player will start playback.
÷ After playback has started, moving the channel fader
slider back to [0] causes the CD player to return to cue
point and enter standby mode (back cue).
* Channel fader is enabled for control only when CROSS
FADER ASSIGN switch is set to [THRU].
14
<DRB1372>
En
[Starting playback with cross fader]
1 Press the FADER START button for the channel (CH-1 to
2 Set the CROSS FADER ASSIGN switch of the selected
3 Move the cross fader slider as far as it will go to the
4 Set a cue point on the CD player, and set to standby at
5 Move the cross fader slider at the desired timing to start
* The fader start function may not operate properly when
Two effectors can be connected if desired.
1. Use the SEND channel selector switch to choose the
2. Use the SEND/RETURN selector switch to choose the
–26 +6
3. Set the SEND/RETURN button to ON.
4. Adjust the RETURN volume with the RETURN dial
CH-6) connected to the CD player you wish to control.
÷ The button of the selected channel will light.
channel to either [A] or [B].
÷ When assigning to channel A (left side) of the cross fader,
set to [A].
÷ When assigning to channel B (right side) of the cross fader,
set to [B].
opposite side of the channel you wish to start.
the cue point.
÷ If a cue point has already been set, the CD player does not
have to be set to standby at the cue point.
playback.
÷ CD player will start playback.
÷ After playback has started, by moving the cross fader slider
all the way, the CD player assigned at the opposite side will
return to cue point and enter standby mode (back cue).
digital connections are made alone. In this event, connect
the CD player's analog connectors as well.

USING EXTERNAL EFFECTORS

source to be sent to the effector.
÷ Select from either [MIC], channel [1]-[6], or [MASTER].
stage to which the effector is connected.
÷ When the send channel is set to [MIC], [INSERT] and [AUX]
switching only are enabled from the same point for both
[PRE] and [POST]. When send channel is set to [MASTER],
only [INSERT] is enabled.
PRE INSERT:
Equalizer output, sent from before the channel fader and
returned to same point.
POST INSERT:
Channel fader output, sent from before the cross fader
assign, and returned to the same point.
AUX:
Channel fader output, sent from before the cross fader
assign and returned to the point before the master fader,
and then added to any other output. The original sound
which has been sent will also be passed through the cross
fader assign and added.
÷ The SEND/RETURN button flashes.
(LEVEL).
Position
PRE POST
Source
INSERT
MIC
CH-1 — CH-6 PRE
MASTER
EQUALIZER CH. FADER
SEND/RETURN SEND/RETURN
ON
LEVEL
POST INSERT
PRE INSERT
SEND
AUX PRE POST AUX PRE POST
INSERT INSERT
INSERT AUX
POST AUX
INSERT
C. F. ASSIGN CROSS FADER MASTER FADER
ON
ON
LEVEL
SEND/RETURN
POST
INSERT
PRE
INSERT
AUX AUX
RETURN
AUX
LEVEL