Presentation; Dear Customer; Design And Features - Husqvarna K 1270 Manuel D'utilisation

Dear Customer,

Thank you for choosing a Husqvarna product!
It is our wish that you will be satisfied with your product
and that it will be your companion for a long time. A
purchase of one of our products gives you access to
professional help with repairs and services. If the retailer
who sells your machine is not one of our authorised
dealers, ask him for the address of your nearest service
workshop.
This operator's manual is a valuable document. Make
sure it is always at hand at the work place. By following its
content (operating, service, maintenance etc.) the life
span and the second-hand value of the machine can be
extended. If you will sell this machine, make sure that the
buyer will get the operator´s manual.
More than 300 years of innovation
Husqvarna AB is a Swedish company based on a tradition
that dates back to 1689, when the Swedish King Karl XI
ordered the construction of a factory for production of
muskets. At that time, the foundation was already laid for
the engineering skills behind the development of some of
the world's leading products in areas such as hunting
weapons, bicycles, motorcycles, domestic appliances,
sewing machines and outdoor products.
Husqvarna is the global leader in outdoor power products
for forestry, park maintenance and lawn and garden care,
as well as cutting equipment and diamond tools for the
construction and stone industries.
Owner responsibility
It is the owner's/employer's responsibility that the operator
has sufficient knowledge about how to use the machine
safely. Supervisors and operators must have read and
understood the Operator's Manual. They must be aware
of:
• The machine's safety instructions.
• The machine's range of applications and limitations.
• How the machine is to be used and maintained.
National legislation could regulate the use of this
machine. Find out what legislation is applicable in the
place where you work before you start using the machine.
Local regulations could restict the use of this machine.
Find out what regulations are applicable where you work
before you start using the machine.
The manufacturer's reservation
Subsequent to publishing this manual Husqvarna may
issue additional information for safe operation of this
product. It is the owner's obligation to keep up with the
safest methods of operation.
Husqvarna AB has a policy of continuous product
development and therefore reserves the right to modify
the design and appearance of products without prior
notice.
For customer information and assistance, contact us at
our website: www.husqvarna.com
4 – English

PRESENTATION

Design and features

This is a high speed, hand held, power cutter designed to
cut hard materials like masonry or steel and should not be
used for any purpose not described in this manual. Safe
operation of this product requires the operator to read this
manual carefully. Ask your Husqvarna dealer if you need
more information.
Some of the unique features of your product are
described below.
Active Air Filtration™
Centrifugal air cleaning for longer service life and longer
service intervals.
SmartCarb™
Built-in automatic filter compensation maintains high
power and reduces fuel consumption.
X-Torq®
The X-Torq® engine provides a more accessible torque
for a wider range of speeds which results in maximum
cutting capacity. X-Torq® reduces the fuel consumption
by up to 20% and the emissions by up to 60%.
EasyStart
The engine and starter are designed to ensure quick and
easy starting of the machine. Reduces the pull resistance
in the starter cord by up to 40%. (Reduces the
compression during starting.)
Water cooling and dust management
(K 1270)
Less slurry and low water consumption.
Excellent dust control with a wet cutting kit. A progressive
water valve for exact adjustment of the water volume to
efficienty bind the dust and reduce slurry.
Efficient vibration damping system
Efficient vibration dampers spare arms and hands.
Reversible cutting head (K 1270)
The machine is fitted with a reversible cutting head
allowing cutting close to a wall or at ground level,
restricted only by the thickness of the blade guard.
Rail fixture - RA 10, RA 10 S (K 1270 Rail)
Is attached to the rail and drives the cut perpendicular to
the fixture for a straighter cut.