Unpacking And Assembling; Using Further Nozzles (Accessories) - Dirt Devil Swirl Y50 Mode D'emploi

2

Unpacking and assembling

2.1 Unpacking
1. Unpack the appliance and all its accesso-
ries.
2. Check the contents for completeness and
possible damages. Information regarding
scope of delivery (Fig. 1).
ATTENTION:
Always transport or ship the appliance in its
original packaging to avoid damage. Keep
the packaging for such an event.
Dispose of no longer needed packaging
material according to the applicable regula-
tions of your country.
NOTE:
Immediately contact your dealer if you have
found damage resulting from transportation.
2.2 Assembly
WARNING:
Danger of injury! Only assemble the appli-
ance if it is not connected to the power sup-
ply. Otherwise the machine might start up
and parts of your body, hair or pieces of
clothing might be sucked in.
1. Insert the end of the suction hose in the in-
take opening (Fig. 2) of the cylinder vacu-
um cleaner, until it locks with an audible
click.
2
2. Insert the handle (Fig. 3/1) into the upper
end of the telescopic tube (Fig. 3/2).
3
3. Attach the floor nozzle (Fig. 3/3) to the bot-
tom end of the telescopic tube (Fig. 3/4).
NOTE:
It might be necessary to push a bit harder.
4. Adjust the length of the telescopic tube.
Press down the release latch on the tube
(Fig. 4/1) to do this. Then extend the tele-
scopic tube to the desired length. Let go of
the release catch while pulling until it locks
in place. You will hear a distinct click.
4
Your cylinder vacuum cleaner is now ready for
use.
2.3 Using further nozzles (acces-
sories)
Besides the floor nozzle you just attached, you
may extend the functions of your cylinder vac-
uum cleaner with other nozzles.
„
The supplied accessories include:
5
- Crevice nozzle (Fig. 5/1)
For vacuuming spots difficult to reach.
- Furniture brush (Fig. 5/2)
For cleaning delicate surfaces.
- Upholstery nozzle (Fig. 5/3)
For gentle vacuuming of upholstered fur-
niture.
„
Optionally available are:
6
- Turbo brush (Fig. 6/1)
For thoroughly deep cleaning of carpets
with the revolving brush head.
ATTENTION:
Our turbo brush serves solely to vacuum
non-sensitive carpets, runners, doormats,
and the like. Do not clean any objects with
the turbo brush that you would not clean
without a second thought with a conventional
brush. Therefore, do not clean furniture, or
materials with a delicate texture, nor any
other high-quality or polished substrates with
the turbo brush. Otherwise material damage
might occur. If in doubt, refrain from using
the turbo brush. In every instance observe
the instructions for care and cleaning of the
respective manufacturer.
Unpacking and assembling
- Parquet brush (Fig. 6/2)
For vacuuming especially delicate surfac-
es (e.g. parquet, laminate) with long, soft
bristles.
„
This is how to attach the nozzles:
WARNING:
Danger of injury! Only assemble the appli-
ance if it is not connected to the power sup-
ply. Otherwise the machine might start up
and parts of your body, hair or pieces of
clothing might be sucked in.
ATTENTION:
Use only intact nozzles. Damaged nozzles
may scratch or damage surfaces and
objects.
1. Switch off the vacuum cleaner and pull the
plug from the mains socket.
2. Pull off the attached nozzle.
3. Attach the desired nozzle to the bottom end
of the telescopic tube (Fig. 7/1) or if neces-
sary directly to the handle (Fig. 8/1).
7
8
ATTENTION:
Using the cylinder vacuum cleaner without a
nozzle attached increases the danger of
accidentally sucking in objects.
4. If possible, store nozzles no longer in use
on the accessory bracket (Fig. 1/2).
11