Using Your Tv; Watching Connected Devices; Selecting Menu Language - JVC LT-39HW45U Guide D'utilisation

Chapter 4
3. Press ▲/▼ to select Tuner mode, then press
◄/► to select Antenna,
Satellite. (Note: Satellite option may not be
available for certain models.)
- Select Antenna.
• Press ▲/▼ to select Channel install, and
press OK/► to enter.
• Select Automatic search (Refer to Figure 2.),
then press OK/► to display Automatic search.
• Press OK to skip the country selection and
enter the next step. Or
your country, then press OK to enter.
• Select Digital & Analogue, Digital or
Analogue, then press OK/► to start the
automatic search, which relates to all DVB-T
digital and/or analogue channels.
- Select Cable.
• Press ▲/▼ to select Channel install, and
press OK/► to enter.
• Select Automatic search, then press OK/► to
display Automatic search.
• Press OK to skip the country selection and
enter the next step. Or use ◄/► to reselect
your country, then press OK to enter.
• - Select Digital & Analogue, then press OK/►
to enter. Select your scan mode if available
and configure proper cable information in the
same way as in Initial setup. Select Scan and
press OK/► to start your automatic search
relating to all DVB-C digital and analogue
channels.
- Select Digital, then follow the same process
as above to start your automatic search
relating to all DVB-C digital channels.
- Select Analogue, then press OK/► to start
your automatic search relating to all analogue
channels.
- Select Satellite.
• Press ▲/▼ to select Satellite setup, and press
OK/► to enter.
• Press ▲/▼ to select a proper satellite or add
new satellites if needed, then press OK to enter
and configure the correct information relating to
satellite and antenna.
• Select Setup > Channel install > Automatic
search, then press OK/► to enter.
- Select Country, and use ◄/ ► to reselect
your desired country, if necessary.
- Select Satellite tuning, press OK/► to
display Automatic search. Configure the
proper information. Select Scan, and press
OK/► to start initial setup relating to all
satellite channels.
4. The search may take a few minutes. During the
process, you can press MENU to abort halfway.
5. Once the automatic search ends, press MENU to
return to the previous step or press OK to restart
your channel search.
Cable or
use ◄/► to reselect
EN 6
6. After the automatic search, channels are arranged
in a preset order. You can skip channels, modify
the preset order or rename channels.

Using your TV

Accessing channels
Using the alphanumeric buttons: press the
corresponding alphanumeric buttons to access the
channels.
Using the PR+/- or P+/- buttons: scroll through the
channels.

Watching connected devices

Repeatedly press SOURCE on the remote control
to toggle between TV and other input sources, then
press OK. To resume TV viewing, press
button to enter the channel, while P+/- will cycle
through all TV channels and other input sources.
Note: Not all models have OK button on the set.
Volume
Volume control: use the VOL+/- or VOL◄/► buttons
on the TV set or V+/- buttons on the remote control to
increase or decrease the volume.
Sound mute: press the
the sound. Press this button again or the V+ button to
restore it.
Using TV menu
s
1. Press MENU to display the main menu. (Refer to
Figure 3.)
2. Press ▲/▼/◄/ ►to select the desired item, then
press OK to open the corresponding submenu.
3. In submenus, use ▲/▼ to select menu options,
use ◄/ ► to set functions or change values. Use
OK to activate a setting. Use OK/► to open the
corresponding submenu.
4. Press MENU to return to the previous menu.
5. Press EXIT to close the menu.
Note: Some options may not be available for
certain signal sources.

Selecting menu language

You can choose your preferred menu language
following the instructions below.
1. Press MENU to display the main menu.
2. Press ▲/▼/◄/ ►to select Setup, then press OK
to enter.
3. Select Language and press OK/► to enter.
4. Select Menu language and press ◄/► to select
your desired language to display the menus.
5. Press EXIT to close the menu.
Using your TV
any numeric
button to temporarily mute