Technical Data; Noise/Vibration Information - Bosch GSB 1300 Professional Notice Originale

OBJ_BUCH-2421-003.book Page 12 Monday, August 21, 2017 11:52 AM
12 | English
Intended Use
The machine is intended for impact drilling in brick, concrete
and stone as well as for drilling in wood, metal and plastic. Ma-
chines with electronic control and right/left rotation are also
suitable for screwdriving and thread-cutting.
Product Features
The numbering of the product features refers to the illustra-
tion of the machine on the graphics page.
1 Key type drill chuck
2 "Drilling/Impact Drilling" selector switch
3 Lock-on button for On/Off switch
4 On/Off switch
5 Rotational direction switch
6 Wing bolt for depth stop adjustment
7 Wing bolt for adjustment of auxiliary handle
8 Auxiliary handle (insulated gripping surface)
9 Depth stop
10 Handle (insulated gripping surface)
11 Chuck key
12 Screwdriver bit*
13 Universal bit holder*
*Accessories shown or described are not part of the standard de-
livery scope of the product. A complete overview of accessories
can be found in our accessories program.

Technical Data

Impact Drill
Article number
Rated power input
Output power
No-load speed
Impact frequency at no-load
Rated torque
Right/left rotation
Spindle collar dia.
Max. drilling dia.
– Brickwork
– Concrete
– Steel
– Wood
Chuck clamping range
Weight according to EPTA-
Procedure 01:2014
Protection class
The values given are valid for a nominal voltage [U] of 230 V. For differ-
ent voltages and models for specific countries, these values can vary.

Noise/Vibration Information

Sound emission values determined according to
EN 60745-2-1, EN 60745-2-2.
Typically the A-weighted noise levels of the product are:
Sound pressure level 95 dB(A); Sound power level
106 dB(A). Uncertainty K =3 dB.
Wear hearing protection!
1 609 92A 43S | (21.8.17)
Vibration total values a
determined according to EN 60745-2-1:
Drilling into metal: a
Impact drilling into concrete: a
Screwdriving without impact: a
Tapping: a
The vibration level given in this information sheet has been
measured in accordance with a standardised test given in
EN 60745 and may be used to compare one tool with anoth-
er. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main ap-
plications of the tool. However if the tool is used for different
applications, with different accessories or insertion tools or is
poorly maintained, the vibration emission may differ. This
may significantly increase the exposure level over the total
working period.
An estimation of the level of exposure to vibration should also
take into account the times when the tool is switched off or
when it is running but not actually doing the job. This may sig-
nificantly reduce the exposure level over the total working
period.
Identify additional safety measures to protect the operator
from the effects of vibration such as: maintain the tool and the
accessories, keep the hands warm, organisation of work pat-
terns.
Assembly
 Before any work on the machine itself, pull the mains
GSB 1300 plug.
3 601 AA1 0..
Auxiliary Handle (see figure A)
W 550
 Operate your machine only with the auxiliary handle 8.
W 270
The auxiliary handle 8 can be set to any position for a secure
-1
min 0 – 2800
and low-fatigue working posture.
-1
min 0 – 41800
Turn the wing bolt for adjustment of the auxiliary handle 7 in
Nm 1.5 anticlockwise direction and set the auxiliary handle 8 to the
required position. Then tighten the wing bolt 7 again in clock-

wise direction.
mm 43
Adjusting the Drilling Depth
The required drilling depth X can be set with the depth stop 9.
mm 13
mm 13
Loosen the wing bolt for the depth stop adjustment 6 and in-
mm 10
sert the depth stop rod into the auxiliary handle 8.
mm 25
The knurled surface of the depth stop 9 must face upward.
mm 1.5 – 13
Pull out the depth stop until the distance between the tip of
the drill bit and the tip of the depth stop corresponds with the
kg 1.8
desired drilling depth X.
/II
Retighten the wing bolt for the depth stop adjustment 6 again.
Changing the Tool
 Wear protective gloves when changing the tool. The
drill chuck can become very hot during longer work peri-
ods.
Key Type Drill Chuck (see figure B)
Open the key type drill chuck 1 by turning until the tool can be
inserted. Insert the tool.
(triax vector sum) and uncertainty K
h
2
=7.5 m/s , K=1.5 m/s
h
2
=10.5 m/s , K=1.5 m/s
h
2
<2.5 m/s , K=1.5 m/s
h
2 2
<2.5 m/s , K=1.5 m/s
h
2
2
2
Bosch Power Tools