Product Description And Specifications; Product Features; Noise/Vibration Information; Technical Data - Bosch GKF 550 Professional Notice Originale

Product Description and
Specifications
Read all the safety and general instructions.
Failure to observe the safety and general in-
structions may result in electric shock, fire
and/or serious injury.
Please observe the illustrations at the beginning of this oper-
ating manual.
Intended use
The power tool is intended for copy routing as well as routing
grooves, edges, profiles and elongated holes in wood,
plastic and light building materials while resting firmly on the
workpiece.

Product features

The numbering of the product features refers to the diagram
of the power tool on the graphics page.
(1) Drive unit
(2) Routing base
(3) Carbon brush bracket
(4) Nut for routing guide
(5) Chip deflector
A)
(6) Router bit
(7) Cap nut with collet
(8) Guide plate
(9) Base plate
(10) Wing bolt for routing base
(11) On/off switch
(12) Scale for setting routing depth
(13) Collet
(14) Tool holder
(15) Open-ended spanner (10 mm)
(16) Open-ended spanner (17 mm)
A)
(17) Guide bushing
A)
(18) Parallel guide
(19) Wing bolt for parallel guide
A)
(20) Pilot
(21) Wing bolt for fixing the horizontal alignment
(22) Wing bolt for horizontal alignment of the pilot
A)
(23) Guide roller
(24) Handle (insulated gripping surface)
A) Accessories shown or described are not included with the
product as standard. You can find the complete selection of
accessories in our accessories range.

Technical data

Edge router
Article number
Rated power input
Bosch Power Tools
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.

Noise/Vibration Information

Noise emission values determined according to
EN 62841-2-17.
Typically the A-weighted noise level of the power tool are: 83
dB(A); sound power level 94 dB(A). Uncertainty K = 3 dB.
Wear hearing protection!
Vibration total values a
determined according to EN 62841-2-17: a
K = 1.5 m/s
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
A)
over the total working period.
A)
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
A)
Fitting
A)
u
A)
Changing the tool
u
Original router bits from the extensive range of Bosch ac-
cessories are available from your specialist dealer.
Removing the routing base (see figure A)
GKF 550
Before fitting a router bit, you must first separate the routing
3 601 FA0 0..
base (2) from the drive unit (1).
W 550
Edge router
No-load speed
Tool holder
Weight according to
EPTA-Procedure 01:2014
Protection class
(triax vector sum) and uncertainty K
h
2
.
Pull the plug out of the socket before carrying out any
work on the power tool.
Wearing protective gloves while fitting and changing
router bits is recommended.
English | 13
GKF 550
-1
min 33,000
mm 6
inches ¼
kg 1.4
/ II
2
= 3.0 m/s ,
h
1 609 92A 5JF | (14.01.2020)