Cillit Impulsor Optronic F 3 Instructions De Montage Et D'utilisation page 14

Initial star Initial star
Initial star Initial star Initial startup
GB GB GB GB
GB
After checking that the unit has been installed
correctly and after inspecting the current, water
and waste water (according to DIN 1988, part 4),
start the unit as described below:
Undo the childproof lock (11
Run the cable of the transformer plug (1 1 1 1 1 ) through
the connection cable gland (10
Impulsor Optronic
minal A A A A A (polarity is not important).
Plug the transformer plug (1 1 1 1 1 ) into the outlet.
pears on the display, and an audio signal is emit-
ted. These signals indicate that there is no active
substance in the unit.
Connecting the active substance container Connecting the active substance container Connecting the active substance container
Connecting the active substance container Connecting the active substance container
Impulsor Optronic Impulsor Optronic
Impulsor Optronic Impulsor Optronic Impulsor Optronic
1. Undo the childproof lock (11
cap (7 7 7 7 7 ).
2. Remove the aluminium seal from the 3kg min-
eral substance container.
3. Lift the active substance container from the
bottom above the suction pipe (8 8 8 8 8 ) and attach it
by turning it gently. The empty message goes
out, and the audio signal is switched off.
4. Flip down the cap (7 7 7 7 7 ) and screw down the child-
proof lock (11 11 11) to prevent the mineral substance 11 11
container from twisting.
Connect the water flow. The metering unit is now
ready to use.
Impulsor Optronic Impulsor Optronic Impulsor Optronic Impulsor Optronic Impulsor Optronic
1. Undo the childproof lock (11
cap (7 7 7 7 7 ).
2. Connect the suction line (13
(14 14 14) of the suction lance. The suction line is 14 14
marked for suction. It must be pushed onto the
nozzle with the arrow pointing inside the unit.
The return line is connected to the other noz-
zle. Secure both lines using the hose clamps
provided.
3. Insert the plug (12
the socket (B B B B B ) of the electronic controller (5 5 5 5 5 ).
4. Flip the cover (7 7 7 7 7 ) back down and screw down
the childproof lock (11
1 4 1 4 1 4 1 4 1 4
tup tup
tup tup
11 11) and flip up the cap (7 7 7 7 7 ). 11
11
10 10 10) on the rear of the
10
®
module and connect to the ter-
® ® ® ® ® module module F3 F3
module module module F3 F3 F3
11 11
11 11) and flip up the
® ® ® ® ®
module module module module T10/T20 module T10/T20 T10/T20 T10/T20 T10/T20
11) and flip up the 11 11
11
13 13
13) and the return line 13
12 12) of the suction lance (9 9 9 9 9 ) into 12 12
11 11 11 11).
5. Open the 10/20l box or canister of active sub-
stance. Remove any aluminium seals. Insert
the suction lance (9 9 9 9 9 ) into the container and
tighten the lid.
Do not lift or transport the canister by the Do not lift or transport the canister by the
Do not lift or transport the canister by the Do not lift or transport the canister by the Do not lift or transport the canister by the
suction lance handle. suction lance handle. suction lance handle. suction lance handle. suction lance handle.
Connect the water flow. The metering unit is now
ready to use.
Corrosion protection in copper pipes with Corrosion protection in copper pipes with Corrosion protection in copper pipes with Corrosion protection in copper pipes with Corrosion protection in copper pipes with
Impulsor Optronic Impulsor Optronic
Impulsor Optronic Impulsor Optronic Impulsor Optronic
Cu2 Cu2 Cu2 Cu2 Cu2
ap-
The objective of the procedure is to maintain wa-
ter with a pH value between 7.8 and 8.4.
The factor on the electronic controller may need
to be reprogrammed:
First, begin metering using the factory setting (fac-
tor 12). Remove approximately 100 litres of water tor 12 tor 12
tor 12 tor 12
from the system downstream from the metering
unit and upstream from any storage containers.
Next, collect approximately 2 litres of water in a
clean container and measure the pH using a pH
metre.
If the measured pH is less than 7.8
must be moved towards "1" must be moved towards "1" must be moved towards "1" (1 water metre pulse must be moved towards "1" must be moved towards "1"
= 1 metering stroke).
If the measured pH is greater than 8.4
must be moved towards "15" must be moved towards "15" (15 water metre must be moved towards "15" must be moved towards "15" must be moved towards "15"
pulses = 1 metering stroke).
Hold do Hold do Hold down Hold do Hold do wn the T1 and T2 keys simultaneously for wn wn wn
around 2.5 seconds to change the factor. The
display reads "12" (factory setting).
Use the T1 and T1 and T2 T1 and T1 and T1 and
factor between "1" and "15".
Next, hold down the T1 and
ously for around 2.5 seconds ously f ously f or around 2.5 seconds. The new factor is or around 2.5 seconds or around 2.5 seconds
ously f ously f or around 2.5 seconds
stored and the controller returns to normal op-
eration.
Keep measuring and changing the setting until
the measured pH is between 7.8 and 8.4. Flip the
cover back down and tighten the screws on the
childproof lock.
® ® ® ® ® module module T20 and Quantophos T20 and Quantophos
module T20 and Quantophos module module T20 and Quantophos T20 and Quantophos
is less than 7.8, the factor is less than 7.8 is less than 7.8
is less than 7.8
greater than 8.4 greater than 8.4
greater than 8.4, the factor greater than 8.4
T2 T2 keys to select the required T2 T2
T1 and T1 and T1 and T1 and T2 k T2 k T2 k T2 ke e e e e ys sim T2 k ys simultane- ys sim ys sim ys sim
® ® ® ® ®
fac- fac- fac- fac-
factor factor factor
factor
factor factor
factor factor
ultane- ultane- ultane- ultane-