Bosch PSS 300 AE Instructions D'emploi page 11

OBJ_BUCH-2 609 001 140-001.book Page 3 Tuesday, May 24, 2005 9:08 AM
Tool Specifications
Orbital sander
Article number
Rated power input
Preselection of orbital stroke
rate
No-load speed
Orbital stroke rate
Orbit diameter
Sanding sheet dimensions
— Adhesion via Velcro
backing
— Attachment via clamping
Sanding plate dimensions
Weight according to
EPTA-Procedure 01/2003
Protection class
The values given are valid for nominal voltages [U] of
230/240 V. For lower voltage and models for specific coun-
tries, these values can vary.
Please observe the article number on the type plate of your
machine. The trade names of the individual machines may
vary.
Declaration of Conformity
We declare under our sole responsibility that this prod-
uct is in conformity with the following standards or
standardization documents: EN 60745 according to
the provisions of the
98/37/EC.
Dr. Egbert Schneider Dr. Eckerhard Strötgen
Senior Vice President Head of Product
Engineering Certification
Robert Bosch GmbH, Geschäftsbereich Elektrowerkzeuge
Assembly
Dust/Chip Extraction
Integrated Dust Extraction with Dust Box
(see figures C1–C4)
Attach the dust box 3 onto the outlet piece 7 until it
latches.
To empty the dust box 3, pull off the dust box down-
ward.
Before opening the dust box 3, it is recommended to
loosen the dust from the filter element by gently striking
it against a firm support (as shown in the figure).
2 609 001 140 • 24.5.05
PSS 300 AE
3 603 C40 3..
W 250
rpm 7000–12000
opm 14000–24000
mm 1.8
mm 115 x 230
mm 115 x 280
mm 115 x 230
kg 1.9
/II
directives 89/336/EEC,
English–3
Grasp the dust box 3 by the recessed grip, fold the filter
element 8 upward and empty the dust box. Clean the
thin plates of the filter element 8 with a soft brush.
External Dust Extraction (see figure D)
Insert a vacuum hose 9 onto the outlet piece 7. Con-
nect the vacuum hose 9 to a vacuum cleaner. See the
overview for connecting to various vacuum cleaners at
the end of these operating instructions.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimental
to health or carcinogenic, use a special vacuum
cleaner.
Replacing the Sanding Sheet
Before any work on the machine itself, pull the
mains plug.
When attaching a new sanding sheet, remove any dust
or debris from the sanding plate 5 (e. g. with a brush).
To ensure optimum dust extraction, pay attention that
the punched holes in the sanding sheet match with the
holes in the sanding plate.
Sanding Sheets with Velcro Backing
(see figure A)
The sanding plate 5 is fitted with Velcro backing for
quick and easy fastening of sanding sheets with Velcro
adhesion.
Before attaching the sanding sheet 6, free the Velcro
backing of the sanding plate 5 from any debris by tap-
ping against it in order to enable optimum adhesion.
Position the sanding sheet 6 flush alongside one edge
of the sanding plate 5, then lay the sanding sheet onto
the sanding plate and press it against it with a light turn-
ing motion in clockwise direction.
To remove the sanding sheet 6, grasp it at one of the
tips and pull it off from the sanding plate 5.
Sanding Sheets without Velcro Backing
(see figure B)
Lightly lift and unlatch the sanding-sheet clamp 4.
Guide the sanding sheet 6 under the opened rear sand-
ing-sheet clamp 4 to the stop and clamp the sanding
sheet by reinserting the sanding-sheet clamp 4.
Fold the sanding sheet 6 firmly around the sanding
plate. Guide the other end of the sanding sheet 6 under
the front sanding-sheet clamp 4 and clamp the sanding
sheet by reinserting the sanding-sheet clamp 4.
Sanding sheets without holes, e. g. from rolls or by the
meter, can be punctured with the perforating tool 10 for
use with dust extraction. For this, press the machine
with the mounted sanding sheet onto the perforating
tool (see figure E).
To remove the sanding sheet 6, unlatch the sanding-
sheet clamp 4 and pull out the sanding sheet.