Pioneer ELITE BDP-62FD Mode D'emploi page 39

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

Setting
Options
Digital Output
Bitstream
PCM
Reencode
Off
DTS Downmix
Stereo
Lt/Rt
Downsampling
48k
96k
192k
• Sources with sampling frequencies of over 192 kHz cannot be played.
• When playing copyright-protected discs or files, the signals are output with the sampling frequency limited to 48 kHz or below,
regardless of this setting.
DRC (Dynamic Range
Off
Control)
On
Auto
• This affects such audio signals as Dolby Digital, Dolby TrueHD, and Dolby Digital Plus.
• DRC affects audio signals output from the following audio output terminals:
– Linear PCM audio signals output from the DIGITAL OUT or HDMI OUT terminals
• Depending on the disc, the effect may be weak.
• The effect may differ depending on the speakers, the AV amplifier settings, etc.
HDMI Mode
Dual
Separate
Pure Audio
Also refer to Setting the HDMI Mode on page 17.
Color Space
RGB
YCbCr
YCbCr 422
Full RGB
Resolution
Auto
480P/576P
720P
1080I
1080P
Explanation
Select this to output digital audio signals directly.
Select this to output digital audio signals converted to 2-channel audio
signals.
When a BD containing secondary audio and interactive audio is played, the
two audio signals are mixed and converted to Dolby Digital audio or DTS
audio for output.
Select this to output audio signals other than digital audio signals.
DTS-HD Master Audio signals, DTS-HD High Resolution Audio signals or
DTS Digital Surround audio signals converted to linear PCM audio signals
are converted into 2-channel (stereo) signals for output.
DTS-HD Master Audio signals, DTS-HD High Resolution Audio signals or
DTS Digital Surround audio signals converted to linear PCM audio signals
are converted into 2-channel signals compatible with Dolby Surround for
output (when the connected AV receiver or amplifier, etc., is compatible with
Dolby Pro Logic, the AV receiver or amplifier outputs the linear PCM audio
signals as surround audio signals).
Outputs audio signals that are limited to a sampling frequency below the set
sampling frequency from the DIGITAL OUT terminal. Select according to the
performance of the connected device.
Select this to output audio signals without using the DRC function.
Select this to adjust the range between the loudest and softest sounds
(dynamic range) for playback at average volume. Use this when it is hard to
hear dialog or when watching movies at midnight.
Select to switch the DRC setting On/Off automatically according to the input
audio signal from the disc. This only affects Dolby TrueHD signals.
Video and audio are output simultaneously from the two HDMI OUT terminals.
Select this when you want to output video and audio to two TV sets simultaneously.
Select this when you want to output the video and audio separately, the video from
the HDMI OUT (MAIN) terminal, the audio from the HDMI OUT (SUB) terminal.
Select this to enjoy music only with a better sound quality when devices are
connected to both HDMI output terminals. With this setting, music is output
from the HDMI OUT (SUB) terminal only, and video signals are only output
from the HDMI OUT (MAIN) terminal when DISPLAY is pressed.
Select this to output the video signals as RGB signals. Choose this if the
colors seem too faint and the black seems too bright.
Select this to output the video signals as YCbCr 4:4:4 signals.
Select this to output the video signals as YCbCr 4:2:2 signals.
Select this to output the video signals as RGB signals. Choose this if the colors
seem too dense and all the dark colors are displayed in a uniform black.
Select this to choose the resolution of the video signals output from the
HDMI OUT terminal automatically.
Output the video signals from the HDMI OUT terminal with the selected
resolution.
The resolution can be changed by pressing HDMI, but Auto cannot be
selected.
The resolution switches when HDMI is pressed and held for over 2 seconds.
07
39
En

Publicité

Chapitres

Table des Matières
loading

Table des Matières