Error Code Display - Bosch Kiox BUI330 Notice D'utilisation D'origine

English – 8​

Error code display

The eBike system's components are continuously and auto-
matically monitored. If an error is detected, the correspond-
ing error code is displayed on the on-board computer.
The drive may be automatically shut down, depending on the
type of error. However, if you wish to continue cycling, you
Code Cause
410 One or more buttons of the on-board com-
puter are disabled.
414 Operating unit connection problem
418 One or more buttons on the operating unit
are disabled.
419 Configuration error
422 Drive unit connection problem
423 eBike battery connection problem
424 Communication problem between com-
ponents
426 Internal time-out error
430 Internal battery of the on-board computer
is flat
431 Software version error
440 Internal drive unit fault
450 Internal software error
460 Error at USB port
490 Internal fault of the on-board computer
500 Internal drive unit fault
502 Bike light fault
503 Speed sensor fault
504 Speed signal distortion detected.
510 Internal sensor fault
511 Internal drive unit fault
530 Battery fault
531 Configuration error
1 270 020 XBK | (12.03.2019)
will always be able to do so without assistance from the
drive. Before undertaking any other journeys, the eBike
should be checked.
Have all repairs performed only by an authorised bike
u
dealer.
Corrective measures
Check whether any buttons are stuck, e.g. as a result of dirt finding
its way in. Clean the buttons if need be.
Have the connections checked
Check whether any buttons are stuck, e.g. as a result of dirt finding
its way in. Clean the buttons if need be.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Have the connections checked
Have the connections checked
Have the connections checked
Restart the system. If the problem persists, contact your Bosch
eBike dealer. With this error, it is not possible to bring up the wheel
circumference in the basic settings menu or to adjust it.
Charge the on-board computer (in the holder or via the USB port)
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Remove the cable from the USB port of the on-board computer. If
the problem persists, contact your Bosch eBike dealer.
Have the on-board computer checked
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Check the light and the associated wiring. Restart the system. If
the problem persists, contact your Bosch eBike dealer.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Check that the spoke magnet is positioned correctly, and adjust it
if necessary. Check that nothing has been tampered with (tuning).
Drive assistance is reduced.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Switch off the eBike, remove the eBike battery and reinsert the
eBike battery. Restart the system. If the problem persists, contact
your Bosch eBike dealer.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Bosch eBike Systems
Code Cause
540 Temperature error
550 An impermissible load has been detected. Remove the load. Restart the system. If the problem persists, con-
580 Software version error
591 Authentication error
592 Incompatible component
593 Configuration error
595, 596 Communication error
602 Internal battery fault
603 Internal battery fault
605 Battery temperature error
606 External battery fault
610 Battery voltage error
620 Charger fault
640 Internal battery fault
655 Multiple battery faults
656 Software version error
7xx Transmission fault
800 Internal ABS fault
810 Implausible signals from the wheel speed
sensor
820 Fault in the wire to the front wheel speed
sensor
821 to 826 Implausible signals from the front wheel
speed sensor
The sensor disc may be missing, defective
or fitted incorrectly; there is a significant
difference in diameter between the front
wheel and the rear wheel; extreme riding
Bosch eBike Systems
English – ​ 9
Corrective measures
The eBike is outside of the permissible temperature range. Switch
off the eBike system and allow the drive unit to either cool down or
heat up to the permissible temperature range. Restart the system.
If the problem persists, contact your Bosch eBike dealer.
tact your Bosch eBike dealer.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Switch off the eBike system. Remove then reinsert the battery. Re-
start the system. If the problem persists, contact your Bosch eBike
dealer.
Use a compatible display. If the problem persists, contact your
Bosch eBike dealer.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Check the wiring to the transmission and restart the system. If the
problem persists, contact your Bosch eBike dealer.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
The battery is outside of the permissible temperature range.
Switch off the eBike system and allow the battery to either cool
down or heat up to the permissible temperature range. Restart the
system. If the problem persists, contact your Bosch eBike dealer.
Check the wiring. Restart the system. If the problem persists, con-
tact your Bosch eBike dealer.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Replace the charger. Contact your Bosch eBike dealer.
Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Switch off the eBike system. Remove then reinsert the battery. Re-
start the system. If the problem persists, contact your Bosch eBike
dealer.
Contact your Bosch eBike dealer so that they can perform a soft-
ware update.
Please observe the operating instructions provided by the trans-
mission manufacturer.
Contact your Bosch eBike dealer.
Contact your Bosch eBike dealer.
Contact your Bosch eBike dealer.
Restart the system and carry out a test ride lasting at least two
minutes. The ABS indicator light must go out. If the problem per-
sists, contact your Bosch eBike dealer.
1 270 020 XBK | (12.03.2019)