Maintenance And Servicing - Bosch GGS 18V-23 LC Professional Notice Originale

To start the power tool, push the unlocking lever (17) for-
wards and then push the on/off switch (5) up.
To switch off the power tool, release the on/off switch (5).
Inserting the Battery
Use only original Bosch lithium-ion batteries with the
u
voltage stated on the type plate of your power tool.
Using other batteries can lead to injuries and pose a fire
hazard.
Push the charged battery (7) into the base of the power tool
until the battery is securely locked.
Kickback Stop
If there is a sudden kickback in the power tool,
e.g. jamming when carving, the power supply
to the motor will be interrupted electronically.
To restart the tool, set the on/off switch (5) to
the off position and then switch the power tool on again.
Restart Protection
The restart protection feature prevents the power tool from
uncontrolled starting after the power supply to it has been
interrupted.
To restart the tool, set the on/off switch (5) to the off posi-
tion and then switch the power tool on again.
Note: Rapidly switching the power tool off and on again may
trigger the restart protection, meaning the power tool may
not start up even if the on/off switch (5) is pressed. Set the
on/off switch (5) to the off position and then switch the
power tool on again.
Connectivity functions
In conjunction with the GCY 30-4 Bluetooth
Module, the following connectivity functions are available for
the power tool:
– Registration and personalisation
– Status check, output of warning messages
– General information and settings
– Management
Read the corresponding operating instructions for informa-
tion about the GCY 30-4 Bluetooth
Practical advice
With the GCY 30-4 Bluetooth
u
power tool is equipped with a radio interface. Local
operating restrictions, e.g. in aircraft or hospitals,
must be observed.
Move the grinding tool evenly back and forth with light pres-
sure to achieve an optimum work result. Too much pressure
will reduce the performance of the power tool and lead to
faster wear of the grinding tool.
Protect the grinding tools against impact.
u
Recommendations for optimal handling of the battery
Protect the battery against moisture and water.
Only store the battery only within a temperature range of -20
to 50 °C. Do not leave the battery in your car in the summer,
for example.
Bosch Power Tools
Occasionally clean the ventilation slots on the battery using a
soft brush that is clean and dry.
A significantly reduced operating time after charging indic-
ates that the battery has deteriorated and must be replaced.
Follow the instructions on correct disposal.

Maintenance and Servicing

Maintenance and Cleaning
u
u
After-sales service and advice on using products
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
®
Robert Bosch Ltd. (B.S.C.)
Low Energy
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or ar-
range the collection of a product in need of servicing or re-
pair.
®
Low Energy Module.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
®
Low Energy Module, the
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
Dublin 24
Tel. Service: (01) 4666700
Fax: (01) 4666888
Australia, New Zealand and Pacific Islands
Robert Bosch Australia Pty. Ltd.
Power Tools
Locked Bag 66
Clayton South VIC 3169
Customer Contact Center
Inside Australia:
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
the power tool and the ventilation slots clean.
1 609 92A 470 | (26.10.2018)
English | 19