Elica EAL330S1 Guide D'utilisation, D'entretien Et D'installation page 8

7" round transition
Mark holes
1
Select the vent option that your installation will require
and proceed to that section:
Outside top exhaust
(Vertical duct– 3 1 ⁄ "x 10" Rectangular)
4
Use the diagram or the hood as a template and mark the
locations on the cabinet for ductwork, electrical wiring and
keyhole screw slots.
Hood mounting screws (4)
13 ⁄ " (30" hood)
15
1 6
16 ⁄ " (36" Hood)
15
1 6
Cabinet front
Cabinet bottom
5
Vertical duct
5"
1 ⁄ "
1
4
Wood shims (recessed Centerline
bottom cabinets only)
Outside top exhaust (Only recirculating version)
(Vertical duct–7" Round)
Use the diagram or the hood as a template and mark the
locations on the cabinet for ductwork, electrical wiring and
keyhole screw slots.
Hood mounting screws (4)
13 " (30" hood)
15
16
16 " (36" Hood)
15
16
Cabinet front
Cabinet bottom
Access hole for
7" round duct
5"
Wood shims (recessed
Centerline
bottom cabinets only)
Outside rear exhaust
(Horizontal duct– 3 1 ⁄ "x 10" Rectangular)
4
8
13 ⁄ " (30" hood)
15
1 6
16 ⁄ " (36" Hood)
15
1 6
12 ⁄ "
1
2
⁄ "
5 ⁄ "
1
1
4
4
1 ⁄ "
1
4
access hole
1
Electrical access
hole (in cabinet
bottom)
13 " (30" hood)
15
16
16 " (36" Hood)
15
16
12 "
1
2
HOLE 1 "
1
4
8" DIA.
1
Electrical access hole
(in cabinet bottom)
Use the diagram or the hood as a template and mark the
locations on the cabinet for ductwork, electrical wiring and
keyhole screw slots.
3
3
4
Cabinet
bottom
13 " (30" hood)
15
16
16 " (36" Hood)
15
16
Hood mounting
screws (4)
Installation- Recirculating
Use the hood as a template and mark the locations on the
cabinet for the electrical wiring and keyhole screw slots.
Since the hood is to be recirculated (not to be vented outside),
do not cut out any vent openings in the wall or cabinet bottom.
Choose Venting Option
1 The hood can be set to vent outside or to recirculate air
back into the kitchen. The plastic vent lever is located near
the center of the hood opening.
To vent to the outside, make sure the plastic vent lever is
in the HORIZONTAL position (flat against the metal top
of the hood). To recirculate air into the kitchen, make sure
the plastic vent lever is in the VERTICAL position
(flat against the plastic blower housing).
NOTE: In order to change the vent lever position, you will
need to pull the lever out slightly to clear the plastic tabs.
10 ⁄ "
1
2
⁄ "
1
2
10 "
1
For recessed bottom cabinet only
2
1 If the cabinets have front, side or back trim, make 2 wood
"
1
shims the width of the trim and attach them to the cabinet
2
bottom recess on both sides.
See previous page for marking locations.
Cabinet front
"
1 "
1
9
8
16
" Horizontal duct
access hole
5 "5 "
1 1
4 4
12 "
7
16
13 " (30" hood)
15
16
16 " (36" Hood)
15
16
Electrical access hole
Centerline
(in wall)
Set for
Set for
outside venting
recirculating
Stop tab
Stop tab
Hood shown lying upside down