HIKOKI RP 3608DB Mode D'emploi page 17

9. Dump dusts (Fig. 15)
WARNING
○ Be sure to turn off the vacuum switch and disconnect
the battery.
○ This appliance contains dust that is harmful to health.
Discharge and maintenance operations (including
disposal of the dust collection containers) must only be
carried out by qualifi ed specialists wearing appropriate
protective clothing and equipment.
○ Put on a dust mask.
○ Dispose of the vacuumed material in accordance with
legal regulations.
○ Before removing the head, if the appliance is pushed
on its side while the tank contains liquid, the liquid
will get inside the motor or switch region, causing an
electric shock or motor failure.
CAUTION
○ Do not impact the tank, the fi lter, or the head. Otherwise
they will be deformed or damaged.
○ Although it is based on the amount of suction of dusts
and liquids, dump dusts and liquids in the tank at least
once a day and keep the appliance, the fi lter, etc. clean.
Otherwise suction power fall, motor failure, bad smell
or rusting may be caused.
○ Do not hold the clamps when you dump dusts in the
tank. Otherwise the clamps may be damaged.
NOTE
○ When removing the plastic bag fi lled with dust from the
tank, make sure the bag does not become caught on
parts inside the tank.
○ Empty the plastic bag regularly so that it does not
become excessively fi lled with dust.
○ Do not tilt the tank with accessories inserted in the head
or in the tank. Otherwise any part may be damaged.
(1) Remove the clamps (2 pieces) and raise the handle of
the head.
(2) Lightly striking the inner side of the prefi lter several
times, remove dusts attached to the prefi lter.
(3) Tilt the tank and dump dusts.
(4) Attach the dust fi lter, the prefi lter, the head, and the
clamp in the initial positions.
<When using the plastic bag>
Drop the dust which has collected outside the fi lter into
the plastic bag, and after removing the fi lter and fi lter
cage, remove the plastic bag with the dust from the
tank and dispose the bag.
10. Transportation and storage
(1) How to use the handle (Fig. 16)
When carrying or moving the appliance, hold the
handle of the head part. When you do not use the
handle, put it in the head part.
(2) Fixation and release of the caster (Fig. 17)
By lowering the lever of the caster with the brake, the
rotation of the wheel is fi xed. When releasing the fi xed
wheel, raise the lever. When moving with the appliance
on a vehicle, fi x the caster to retain the appliance.
However, when you move the appliance, check that the
caster is released, or the caster will be damaged.
(3) Tool box assembly (2XC only) (Fig. 18)
(4) Store the product. (Fig. 19)
NOTE
○ To store the hose, you can connect both ends or use
the tool box.
○ In addition to connecting the battery to the product, the
battery can be stored in the tool box.
11. How to attach the paper fi lter (Optional) (Fig. 20)
WARNING
○ Be sure to turn off the appliance and remove the
battery.
○ When using a paper fi lter, use it in combination with the
standard dust fi lter and prefi lter.
If the paper fi lter gets torn, dust may get inside the motor,
causing abnormal noise or fi re due to overheating.
CAUTION
○ When using a paper fi lter, avoid sucking in liquids such
as water or wet dust, as this may lead to tearing of the
fi lter.
○ Do not use a fi lter damper.
Doing so can reduce the dust collection capacity.
(1) Open the paper fi lter horizontally so that the suction
hole in the paper fi lter is over the top of the tank.
(2) Before attaching the fi lter to the appliance, bend the
two folds in the cardboard approx. 90° in the direction
of the arrow.
(3) Match the suction hole in the paper fi lter with the
suction opening of the appliance. Insert the fi lter in
the direction of the arrow as shown in the illustration,
so that the cardboard of the paper fi lter goes past the
stopper on the suction opening.
WIRELESS LINKING FUNCTION
By setting this product for "Auto" mode, the ON/OFF
switch of the wireless linked electric power tool connected
by Bluetooth can be used to activate or deactivate this
product.
(For compatible models and specifi cations, refer to the
latest catalogue or consult with the dealer of this product.)
(Fig. 6)
Linking
To simultaneously use this product with an electric
power tool with wireless linking function, pair the units by
Bluetooth connection when starting work.
Make sure that the electric power tool and this product is
connected by hose before taking the following steps to
establish a connection.
(It does not matter whether you start the instructions with
this product or the electric power tool.)
This Product (Fig. 21)
Turn ON the power
switch
Begin search
(Select "Auto" with the
Auto/Manual switch)
Connection (Pairing)
complete*
* Requires 1 to 3 seconds (time may vary depending
on distance and obstructions) for both units to search
(fl ashing lamps) and establish a connection (lamps lit).
NOTE
○ Two or more devices cannot be connected to the
cleaner at the same.
○ It will take approximately 0.5 seconds for the product to
activate after switching ON the electric power tool.
Also, when you switch OFF, the product will stop a few
seconds later to complete vacuuming the waste in the
hose.
○ While searching for a connected device (indicated by a
fl ashing display lamp), drawing the switch of the power
tool will activate its motor.
(The cleaner's motor will not activate during a search.)
Upon completion of the search (indicated by a lit lamp),
the cleaner will be activated.
○ When pairing multiple sets, pair one set at a time.
○ While in Auto mode, the product will be automatically
powered OFF if there is no operation for two hours.
○ The eff ective range for wireless linking is approximately
10 m.
This range may be shortened by obstructions between
this product and the electric power tool.
17
English
Bluetooth Compatible
Product (Fig. 22)
Draw the switch once
Begin search
(Press the wireless link
switch)
Connection (Pairing)
complete*