Bosch GDB 350 WE Professional Notice Originale page 19

Diamond drill
– 1st gear
– 2nd gear
– 3rd gear
Tool holder
Max. pressure of water supply
Weight according to
EPTA-Procedure 01:2014
Protection class
Dimensions (including de-
tachable parts of the tool)
The specifications apply to a rated voltage [U] of 230 V. These spe-
cifications may vary at different voltages and in country-specific mod-
els.
Drill stand for diamond drills
Article number
Dimensions
– Height
– Width
– Depth
Dimensions of core bit, max.
– Diameter
– Diameter with spacer
plate (29)
– Diameter with water collec-
tion ring
– Length
Drill stroke max.
Working length max.
Weight according to
EPTA-Procedure 01:2014
Noise information
Noise emission values determined according to
EN 62841‑3‑6.
Typically the A-weighted noise level of the power tool is:
Sound pressure level 96 dB(A); sound power level
110 dB(A). Uncertainty K=3 dB.
Wear hearing protection
The noise emission value given in these instructions has
been measured in accordance with a standardised measur-
ing procedure and may be used to compare power tools. It
may also be used for a preliminary estimation of noise emis-
sions.
The noise emission value given represents the main applica-
tions of the power tool. However, if the power tool is used
for other applications, with different application tools or is
poorly maintained, the noise emission value may differ. This
may significantly increase noise emissions over the total
working period.
Bosch Power Tools
To estimate noise emissions accurately, the times when the
GDB 350 WE
tool is switched off, or when it is running but not actually be-
mm 165–350
ing used, should also be taken into account. This may signi-
mm 80–160
ficantly reduce noise emissions over the total working
period.
mm 55–105
1 1/4" UNC
Assembly
bar 3
kg 11.9 Pull the plug out of the socket before carrying out any
u
work on the power tool.
/ I
Assembling the drill stand
mm 534 × 142 × 168
Carrying handle
Before initial commissioning, screw the drill stand carrying
handle (11) firmly in place on the drill column using the
screws (12). In doing so, position the cap of the carrying
handle so that it closes in line with the drill column.
GCR 350
Star handle
3 601 A90 200
Screw the three handlebars of the star handle (15) all the
way into the central hub of the star handle.
mm 955
The star handle (15) serves both as the feed crank during
mm 323
drilling and as a means of loosening or tightening screws on
mm 388
the drill stand.
To drill, push the star handle all the way to the left or right
(as required) and onto the feed pinion (26). Pull the star
mm 300
handle off firmly to remove it.
mm 350
Feed lock with locking brake
Lock the feed when performing any work on the drill stand,
mm 202
during breaks and when not using the drill stand. Do this by
engaging the locking brake (16).
mm 530
To drill, loosen the locking brake (16) until the star
mm 580
handle (15) is easy to move. When doing so, hold the star
handle in place to prevent the power tool from sliding down
mm 550
in an uncontrolled manner.
kg 12.6
Attaching the carrying handle to the power tool
Before initial commissioning, screw the carrying handle (9)
firmly in place on the power tool using the screws (10).
Inserting the power tool (see figures A–B)
Ensure that the locking brake (16) is on.
The drill holder (27) has a recess on the right-hand side.
When placing the machine adapter (25) onto the power tool,
ensure that the flange on the machine adapter also sits on
the right as shown in the diagram B.
Position the machine adapter (25) on the power tool so that
the feather keys (24) of the machine adapter click into the
corresponding recesses of the power tool. Insert the four
screws (23) of the machine adapter and tighten them using
a hex key (size 6 mm).
Loosen the eccentric bolt (14) using the star handle (15)
and pull it as far as possible out of the drill holder (27). Use
the machine adapter (25) to hang the power tool in the drill
holder so that the lower lip of the machine adapter sits be-
hind the lower bolt of the drill holder ➊.
English | 19
1 609 92A 4NK | (03.04.2019)