Milwaukee HEAVY DUTY M18 FCOS230 Notice Originale page 14

industrial chemicals, and bleach or bleach containing products,
etc., can cause a short circuit.
WARNING This device contains a lithium
button/coin cell battery. A new or used battery can
cause severe internal burns and lead to death in
as little as 2 hours if swallowed or enters the
body. Always secure the battery cover. If it does
not close securely, stop using the device, remove the batteries,
and keep it away from children. If you think batteries may have
been swallowed or entered the body, seek immediate medical
attention.
SPECIFIED CONDITIONS OF USE
The cut-off machine is intended for cutting metal, stone and
ceramic materials.
Please refer to the instructions supplied by the accessory
manufacturer.
Do not use this product in any other way as stated for normal
use.
WHEEL SELECTION
Cutting surface Cutting disc type
Non-metallic materials Silicone carbide abrasive
cutting disc
Metallic materials Aluminum oxide abrasive
cutting disc
Masonry materials Diamond wheel with water supply or
silicone carbide abrasive
cutting disc
WATER CONNECTION
A water connection is available on the tool to cool the wheel
and reduce the formation of dust. The water connection should
be used on all concrete cutting applications.
For best results, allow the water to coat the entire cutting wheel
before operation.
ONE-KEY™
To learn more about the ONE-KEY functionality for this tool,
please reference the Quick Start guide included with this
product or go to www.milwaukeetool.com/one-key. To download
the ONE-KEY app, visit the App Store or Google Play from your
smart device.
Also, when the product experiences ESD, the Bluetooth
communication will be disconnected. It needs to be reset
manually to recover.
We considered the results to be within our minimum acceptable
performance level according to EN 55014-2 / EN 301489-1 /
EN 301489-17.
ONE-KEY™ Indicator
Solid Blue Wireless mode is active and ready to be
confi gured via the ONE-KEY™ app.
Blinking Blue Tool is actively communicating with the
ONE-KEY™ app.
Blinking Red Tool is in security lockout and can be unlocked
by the owner via the ONE-KEY™ app.
26 ENGLISH
BRAKING SYSTEM
The run-on brake engages when the trigger is released,
causing the tool to stop within seconds.
Make sure that the insertion tool comes to a complete stop
before laying it down.
In comparison with tools without a run-on brake the run-on time
will be highly reduced by braking.
If the time between releasing the switch and the stop of the
insertion tool increases to much, please have the tool serviced
by an authorized MILWAUKEE service facility.
BATTERIES
Battery packs which have not been used for some time should
be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the
performance of the battery pack. Avoid extended exposure to
heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully
charged, after used.
To obtain the longest possible battery life remove the battery
pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C
and away from moisture
Store the battery packs in a 30% - 50% charged condition
Every six months of storage, charge the pack as normal.
BATTERY PACK PROTECTION LI-ION BATTERY
The battery pack has overload protection that protects it from
being overloaded and helps to ensure long life.
Under extreme stress the battery electronics switch off the
machine automatically. To restart, switch the machine off and
then on again. If the machine does not start up again, the
battery pack may have discharged completely. In this case it
must be recharged in the battery charger.
TRANSPORTING LITHIUM BATTERIES
Lithium-ion batteries are subject to the Dangerous Goods
Legislation requirements.
Transportation of those batteries has to be done in accordance
with local, national and international provisions and regulations.
• The user can transport the batteries by road without further
requirements.
• Commercial transport of Lithium-Ion batteries by third parties
is subject to Dangerous Goods regulations. Transport
preparation and transport are exclusively to be carried out by
appropriately trained persons and the process has to be
accompanied by corresponding experts.
When transporting batteries:
• Ensure that battery contact terminals are protected and
insulated to prevent short circuit.
• Ensure that battery pack is secured against movement within
packaging.
• Do not transport batteries that are cracked or leak.
Check with forwarding company for further advice
MAINTENANCE
The ventilation slots of the machine must be kept clear at all
times.
Use only Milwaukee accessories and spare parts. Should
components need to be replaced which have not been
described, please contact one of our Milwaukee service agents
(see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please
state the machine type printed as well as the six-digit No. on
the label and order the drawing at your local service agents or
directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10,
71364 Winnenden, Germany.
EC-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility
that the product described under "Technical Data" fulfi lls all the
relevant regulations and the directives 2011/65/EU (RoHS),
2014/53/EU, 2006/42/EC, and the following harmonized
standards have been used:
EN 60745-1:2009+A11:2010
EN 60745-2-22:2011+A11:2013
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 62479:2010
EN 301 489-1 V2.2.3
EN 301 489-17 V3.1.1
EN 300 328V2.2.2
EN IEC 63000:2018
Winnenden, 2021-01-26
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
GB-DECLARATION OF CONFORMITY
We declare as the manufacturer under our sole responsibility that
the product described under "Technical Data" fulfi lls all the relevant
provisions of the following Regulations S.I. 2008/1597 (as
amended), S.I. 2017/1206 (as amended), S.I. 2012/3032 (as
amended) and that the following designated standards have been
used:
BS EN 60745-1:2009+A11:2010
BS EN 60745-2-22:2011+A11:2013
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN 62479:2010
EN 301 489-1 V2.2.3
EN 301 489-17 V3.1.1
EN 300 328V2.2.2
BS EN IEC 63000:2018
Winnenden, 2021-01-26
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany
SYMBOLS
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on
the machine.
Please read the instructions carefully before starting
the machine.
Always wear goggles when using the machine.
Wear ear protectors!
Wear a suitable dust protection mask.
Wear gloves!
Do not use force.
Only for cutting work.
Do not swallow the coin cell battery!
Do not dispose of electric tools together with
household waste material.
Electric tools and electronic equipment that have
reached the end of their life must be collected
separately and returned to an environmentally
compatible recycling facility.
Check with your local authority or retailer for recycling
advice and collection point.
Rotation direction
n
Rated speed
V
Volts
Direct current
European Conformity Mark
British Confomity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark
ENGLISH 27