Publicité
Les langues disponibles
Les langues disponibles
the snap hook of the shoulder strap (Fig.
14/
). To unfasten the belts, press the
a
button on the central buckle (fig. 14/
Optional harness systems (reins), in ac-
cordance with the European standard EN
13210: 2004 and the British BS 6684, can
be attached to the stroller using the "D"
shaped rings on the sides of the seat (Fig.
14/c).
WARNING!
Always use the stroller with
the child strapped with the safety harness
together with the crotch strap.
FRONT BUMPER BAR
15.
Insert the front bumper bar in the slots of
the armrests until it locks with a click (Fig. A
and B). Make sure that the hook on/off tabs
of the bumper bar are pointing downwards.
The bumper bar is partially openable from
both sides and fully removable to facilitate
positioning of the child. To remove it, press
the hook on/off tabs on the bumper bar
hooks under the armrests and remove the
bumper bar by pulling it towards you.
ASSEMBLING THE ACCESSORIES
CANOPY
16.
The canopy fastens onto special plastic
compartments placed along the side tubes
of the frame. To remove the canopy, pro-
ceed with the operation in reverse order
(Fig. A and B).
17.
Open the canopy by pulling the bow forward
and lock it by pushing the side joints (Fig.
A and B). Attach the back in fabric with
the special Velcro straps on the sides of
the seat.
18.
The canopy includes a further folding rear
extension to better protect your child from
the sun (Fig. A and B).
19.
To open the collapsible hood unfasten the
specific button (Fig. A and B). To protect
your child from the sun, turn the canopy
forward into the desired position.
BASKET
Basket included in the package. The storage
basket is fastened to the stroller through
the base hooks. It is not suitable to carry
loads in excess of 3 kg.
FULL RAINCOVER
20.
The raincover goes over the stroller, carrycot
).
and car seat, securing it to the frame using
b
the specific Velcro straps. The raincover is
universal, hence the dressing can be slightly
abundant in the stroller and stroller with
car seat versions.
LEG COVER
21.
The leg cover for the stroller is standard-
ised with the carrycot one. Remove the
leg cover of the carrycot and pass it under
the front bumper bar and secure it to the
stroller.
CLOSING THE STROLLER
To close the stroller please follow this pro-
cedure.
22.
Close the canopy by releasing the joints
on both sides.
23.
Block the front wheels. They should not
remain in swivel mode but should always
be locked by lifting both levers.
24.
Grasp the handle on the back of the stroller
and retract it upwards (Fig. A) then hold
the stroller by pushing both closure but-
tons on the handles (Fig. B) and push down
simultaneously to release the frame on the
front (see Fig. 24/
A-24/
B).
a
a
25.
To close the stroller completely, push both
handles downwards simultaneously until
you hear a click.
26.
Now the stroller is closed and can stand
on its own (Fig. 26/
).
a
CARRYCOT
THE CARRYCOT FASTENS ONTO THE STROLLER
THROUGH A PRACTICAL AND QUICK COUPLING
SYSTEM.
WARNING!
THE CARRYCOT IS APPROVED
FOR TRANSPORT BY CAR. THE "CAR KIT" IS
NOT INCLUDED IN THE PACKAGE. REFER TO
THE USER MANUAL OF THE "CAR KIT" FOR ALL
INFORMATION CONCERNING ASSEMBLY OF THE
"CAR KIT" ON THE CARRYCOT, THE INSTALLA-
TION OF THE CARRYCOT IN THE CAR AND ITS
USE DURING TRAVEL.
27.
Use the stroller structure without backrest,
canopy and front bumper bar.
28.
Position the carrycot on the stroller.
30
29.
Make sure it is properly in place (the pins
placed under both sides of the carrycot
spoiler must enter in the appropriate grafts
on the armrests of the stroller until you
hear a fastening "click"). The handlebar
of the pram can be positioned vertically
or horizontally (Fig. 29/
) by pressing on
a
the two side buttons of the handlebar.
WARNING!
Always make sure that the
carrycot is securely attached to the stroller
on both sides, by pushing with both hands
on the product.
30.
The carrycot is equipped with a pad to be
placed under the mattress to raise the
child slightly.
DISASSEMBLY
31.
To remove the carrycot, be sure the han-
dlebar is in the upright position (Fig. A).
Push the button positioned on both sides
placed under the carrycot handlebar (Fig.
B) and release the carrycot at the same
time by lifting it vertically from the stroller
(Fig. C).
BLANKET
32.
The carrycot is equipped with a leg cover
blanket for colder months. The inner fab-
ric lining of the carrycot is washable with
mild soap in lukewarm water. Light stains
can be cleaned with a sponge and soapy
water. Do not use bleach, do not iron, do
not machine wash, do not tumble dry.
WARNING!
Pay attention to the danger
of an open flame or strong heat sources
near the baby carrier bag. Do not use the
carrycot on a support.
CAR SEAT
ASSEMBLY ON THE STROLLER FRAME
USE OF THE CAR SEAT
THE CAR SEAT ATTACHES TO THE STROLLER
THROUGH A PRACTICAL AND QUICK COUPLING
SYSTEM.
33.
Use the stroller structure without backrest,
canopy and front bumper bar.
34.
Place the car seat as shown in the figure.
35.
Make sure it is properly in place (the pins
placed under both sides of the carrycot
handle must enter in the appropriate grafts
on the armrests of the stroller until you
hear a fastening "CLICK").
DISASSEMBLY
36.
To remove the car seat from the stroller,
press the release buttons on the sides of
the car seat and simultaneously lift the
seat vertically from the stroller frame.
HANDLE
37.
The handle can be adjusted in 3 positions, by
pressing both release buttons and bringing
it into the desired position (see direction
of arrow). Then release the buttons (Fig.
A, B, C).
SAFETY BELTS
38.
Open the safety belts and place the child on
the seat. Join the shoulder strap buckles.
Insert them in the central buckle until it
clicks into place.
39.
Make sure the belt is properly closed.
40.
Adjust the tension of the belts with the
adjustment strap pulling the front strip that
comes out of the lining (Fig. 3). To loosen
the tension of the belts, press the button
on the front of the chair, under the tissue
flap (Fig. 1). Hold the shoulder straps at the
same time and pull towards you (Fig. 2).
To open the belts press the safety button
at the centre of the buckle (see detail in
the circle).
WARNING!
Always make sure that your
child is securely fastened to the car seat
belts.
CORRECT POSITION OF SAFETY BELTS
41.
The safety belts can be adjusted in 3 dif-
ferent heights.
42.
Remove the two safety belts from the slit
of the bodywork and from the lining of the
car seat towards the rear.
43.
Once you have selected the desired height,
insert the straps again in the bodywork slit
and in the car seat lining one.
WARNING!
Belts must always be used
properly. They must always be well ten-
sioned, adhering to the body of the child,
not twisted, and properly fastened.
WARNING!
THE CAR SEAT MUST NOT BE
USED IN LIEU OF THE BOUNCER. WHEN THE
31
Publicité
