The Program Process Of The Breadmaker; Cleaning And Maintenance - Unold Backmeister 8690 Notice D'utilisation

the Program Process oF the Breadmaker

1. Inserting the Bread pan
Hold the non-stick bread pan with both hands and slide it slightly
inclined on the socle inside the baking chamber. Turn the bread
pan clockwise, until it clicks into position. Fill the holes of the
kneading blade with heat resisting margarine before fitting it into
the bread pan. This avoids that dough penetrates and bakes into
the kneading blade.
2. Pouring in the ingredients
The ingredients must be poured into the pan in the order
prescribed in the recipe.
In case of very heavy dough, e.g. with a high rye portion, we
recommend to fill in first the liquid, then the flour and other
ingredients and finally the yeast to ensure better kneading results.
When using the time preset function, it must be ensured that no
contact between the water and the yeast takes place before the
program is started.
3. selecting the program process
Select the required program process with the menu button.
Select the stage appropriate for the program. Select the required
browning. You can set a delay with the timing button. Press the
START button. After pressing START further corrections are no
more possible.
4. Mixing and kneading dough
The Breadmaker mixes and kneads the dough automatically as
long as necessary to reach the proper consistency.
5. Pause
After each kneading process there is a pause to allow the liquid to
slowly penetrate the yeast and the flour.

cleaning and maintenance

1. Before the Backmeister
baking container and kneader with warm water and a mild
washing-up liquid.
2. always allow the breadmaker to cool down before it is cleaned
and stored. It takes approximately 30 minutes for the breadmaker
to cool down before it can be used again for baking and dough
preparation.
3. Always switch off the appliances at the ON/OFF switch,
disconnect the power supply plug from the mains, and allow
the breadmaker to cool down, before it is cleaned. Always
use a mild washing-up liquid. Never use chemical cleaners,
benzine, oven cleaners and scouring agents.
4. Remove all ingredients and crumbs from the lid, case and
baking chamber with a moist cloth. Never immerse the
breadmaker in water and never fill the baking chamber with
water. The lid can be removed for easy cleaning be removing
the cover of the hinge and then pullig off the lid.
5. Wipe the baking tin with a moist cloth. The inside of the tin
can be rinsed with warm water and a washing-up liquid. Do
not soak the tin in water for prolonged periods.
6. Both the kneader and driving shaft should be cleaned
immediately after use. The kneader may be difficult to
30
is used for the first time, wash the
®
6. Dough raising
After each kneading phase the Breadmaker produces the optimal
temperature for the rising of the dough.
7. Baking
The bread baking automatic regulates the baking temperature
and the timing automatically.
8. Keeping warm
When the baking is over, a beep sound indicates that the bread
or food can be removed. At the same time a keep-warm time of
1 hour starts. If you want to remove the bread before the keep-
warm phase has ended, just press the STOP button and take out
the bread.
9. end of the program process
After the end of the program process, take out the pan with the
help of handcloths by turning it counter-clockwise. Stand it on end
and, when the bread does not immediately fall onto the cooling
wire, waggle the kneading drive from below until the bread falls
out. Do not knock the bread pan on an edge or table, as the warm
bread pan may be deformed.
If the kneader sticks in the bread, use the hook to remove it.
Push it on the underside of the still-warm bread in the (almost)
round opening of the kneader and fold it on the bottom edge of
the kneader, ideally at the point where the kneader blade is. Then
pull the kneader up with the hooked skewer. You can then see
where the blade is in the bread.
remove if it remains in the baking tin. In such an event fill the
container with warm water and allow it to soak for approx. 30
minutes. The kneader can then be easily removed for cleaning.
7. The bread pan is equipped with a high quality QUANTANIUM
Never use metal objects or scourers to clean the surface of the
non-stick container. It is normal for the colour of the non-
stick surface to change in the course of time. This does not
influence the non-stick function.
8. Condensation from the steam accumulates between the inside
and outside lid during baking and flows off the lid when baking
has been completed. This is normal. Any discolouration of
the lid is of no consequence, but it can be removed with an
appropriate cleaner.
9. Before the breadmaker is packed away for storage ensure that
it has completely cooled down, is clean and dry, and that the
lid is closed.
-.
®