Practical Advice; Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch GSR 12V-15 FC Professional Notice Originale

10 | English
battery (5) into the handle until you feel it engage and it is
flush with the handle.
Setting the rotational direction (see figure H)
The rotational direction switch (6) is used to change the ro-
tational direction of the power tool. However, this is not pos-
sible while the on/off switch (7) is being pressed.
Right rotation: To drill and to drive in screws, press the ro-
tational direction switch (6) through to the left stop.
Left Rotation: To loosen and unscrew screws and nuts,
press the rotational direction switch (6) through to the right
stop.
Preselecting the Torque
The torque presetting ring (2) can be used to preselect the
required torque in 15 stages. When the correct setting is
used, the application tool will be stopped when the screw is
driven flush into the material or once the set torque has been
reached. In position the overload clutch is deactivated,
e.g. for drilling.
When unscrewing screws, it may be advisable to select a
higher setting or the symbol.
Mechanical gear selection
Only operate the gear selector (3) when the power
u
tool is not in use.
You can preselect two speed ranges with the gear selector
(3).
Gear I:
Low speed range; for screwdriving or working with a large
drilling diameter.
Gear II:
High speed range; for working with a small drilling diameter.
Always push the gear selector switch as far as it will
u
go. Otherwise, the power tool may become damaged.
Switching on/off
To start the power tool, press and hold the on/off switch
(7).
The worklight (9) lights up when the on/off switch (7) is
lightly or fully pressed, allowing the work area to be illumin-
ated in poor lighting conditions.
The worklight (9) will remain lit for approximately ten
seconds after the on/off switch (7) has been released.
Adjusting the Speed
You can adjust the speed of the power tool when it is on by
pressing in the on/off switch (7) to varying extents.
A light pressure on the on/off switch (7) results in a low rota-
tional speed. Increased pressure on the switch causes an in-
crease in speed.
Fully automatic spindle lock (Auto-Lock)
The drill spindle, and therefore the holder (1), are locked
when the on/off switch (7) is not pressed.
This enables screws to be screwed in even when the battery
is empty and allows the power tool to be used as a screw-
driver.
1 609 92A 53J | (03.07.2020)
Temperature-dependent overload protection
In normal conditions of use, the power tool cannot be over-
loaded. If the power tool is overloaded or not kept within the
permitted operating temperature range, the power output is
reduced or the power tool is switched off. The power tool
will not run at full power output again until the permitted op-
erating temperature has been reached.
Battery charge indicator
When the on/off switch (7) is pressed in halfway or com-
pletely, the battery charge-control indicator (8) indicates
the charge condition of the battery for several seconds. The
indicator consists of three green LEDs.
LEDs
3× continuous green light
2× continuous green light
1× continuous green light
1× flashing green light

Practical advice

Only apply the power tool to the screw when the tool
u
is switched off. Rotating application tools can slip off.
After working at a low speed for an extended period, you
should operate the power tool at the maximum speed for ap-
proximately three minutes without load to cool it down.
When drilling into metal, only use sharpened HSS drills (HSS
= high-speed steel) which are in perfect condition. The
Bosch accessory range guarantees appropriate quality.
Before screwing larger, longer screws into hard materials, it
is advisable to pre-drill a pilot hole with the core diameter of
the thread to approx. 2/3 of the screw length.

Maintenance and Service

Maintenance and Cleaning

Remove the battery from the power tool before carry-
u
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
To ensure safe and efficient operation, always keep
u
the power tool and the ventilation slots clean.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Capacity
≥66 %
≥33 %
<33 %
Reserve
Bosch Power Tools