Technical Data; Noise/Vibration Information - Bosch PST 750 PE Notice Originale

Technical Data

Jigsaw
Article number
Cut Control Cut Control
Stroke rate control
Pendulum action
Rated power input
Power output
No-load stroke rate n
0
Stroke
Max. cutting depth
– in wood
– in aluminium
– in steel (unalloyed)
Max. cutting angle (left/right)
Weight according to EPTA-Procedure 01:2014
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-specific models.

Noise/Vibration Information

Noise emission values determined according to
EN 62841-2-11.
Typically, the A-weighted noise level of the power tool is:
Sound pressure level 85 dB(A); sound power level
96 dB(A). Uncertainty K=5 dB.
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-11:
Cutting boards with saw blade T 144 D:
2 2
a =13 m/s , K=3 m/s ,
h,B
Cutting sheet metal with saw blade T 118 A:
2 2
a =7 m/s , K=1.5 m/s .
h,M
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Bosch Power Tools
PST 750 PE PST 750 PEL
3 603 CA0 5.. 3 603 CA0 6..
−
●
●
W 530
W 290
−1
min 500–3000
mm 20
mm 75
mm 12
mm 5
° 45
kg 1.9
/II
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Assembly
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Inserting/changing the saw blade
When fitting or changing the saw blade, wear protect-
u
ive gloves. Blades are sharp and can become hot when
used for prolonged periods of time.
Selecting the saw blade
You will find an overview of recommended saw blades at the
end of these operating instructions. Only use saw blades
with a single lug shank (T shank) or with a 1/4" universal
shank (U shank). The saw blade should not be longer than
required for the intended cut.
Use a narrow saw blade when sawing tight curves.
Inserting the saw blade (see figure A)
Clean the shaft on the saw blade before inserting it.
u
A dirty shaft cannot be securely fixed in place.
PST 800 PEL/PST 8000 PEL/PST 8500 PEL: Remove the
hood (9) if required.
Push the saw blade receptacle (13) upwards in the direction
of the arrow. Push the saw blade (15), with the teeth in the
cutting direction, into the saw blade receptacle as far as it
will go.
English | 15
PST 800 PEL
PST 8000 PEL
PST 8500 PEL
3 603 CA0 1..
− ●
● ●
● ●
520 530
290 290
500–3000 500–3000
20 20
75 80
12 12
5 5
45 45
1.9 1.9
/II /II
1 609 92A 51A | (09.04.2019)