Maintenance And Service; Maintenance And Cleaning; After-Sales Service And Application Service - Bosch PKP 3,6 LI Notice Originale

12 | English
Problem Cause
Workpiece is melting. Workpiece is made of a material with too
low a melting point, e.g. Styrofoam
Fingers are being burned Adhesive is puncturing paper when applied Do not hold the workpiece in your hands
while gluing.
Adhesive is puncturing threads when ap-
plied
Metal workpiece is heating up

Maintenance and Service

Maintenance and Cleaning

Warning! Switch the glue gun off before commencing
u
maintenance and cleaning work.
Keep the glue gun clean to ensure effective, safe oper-
u
ation.
After the adhesive has hardened, you can remove it with a
blunt object. Do not use solvents when cleaning. If neces-
sary, the bonding locations can be unstuck again by applying
heat.
An inserted glue stick (4) must not be removed from the rear
of the glue gun.

After-Sales Service and Application Service

Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. You can find explosion drawings and information on
spare parts at: www.bosch-pt.com
The Bosch product use advice team will be happy to help you
with any questions about our products and their accessor-
ies.
In all correspondence and spare parts orders, please always
include the 10‑digit article number given on the nameplate
of the product.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
You can find further service addresses at:
www.bosch-pt.com/serviceaddresses
Transport
The contained lithium-ion batteries are subject to the Dan-
gerous Goods Legislation requirements. The batteries are
1 609 92A 5TJ | (23.07.2020)
Remedy
Hot melt adhesive is not suitable, use special adhes-
ive
Carry out gluing on a heatproof silicone mat
Do not hold the workpiece in your hands
Carry out gluing on a heatproof silicone mat
Do not hold the workpiece in your hands
Carry out gluing on a heatproof silicone mat
Clamp the workpiece
suitable for road-transport by the user without further re-
strictions.
When shipping by third parties (e.g.: by air transport or for-
warding agency), special requirements on packaging and la-
belling must be observed. For preparation of the item being
shipped, consulting an expert for hazardous material is re-
quired.
Disposal
Glue guns, power supplies, batteries, accessor-
ies, packaging and adhesive residues should be
recycled in an environmentally friendly manner.
Do not dispose of glue guns, power supplies or
batteries with household waste.
Only for EU countries:
In accordance with Directive 2012/19/EU and Directive
2006/66/EC respectively, electrical and electronic equip-
ment that is no longer usable and defective/drained batter-
ies must be collected separately and recycled in an environ-
mentally friendly manner.
Battery packs/batteries:
Li-ion:
Please observe the notes in the section on transport (see
"Transport", page 12).
Integrated batteries may only be removed for disposal
u
by qualified personnel. Opening the housing shell can ir-
reparably damage the glue gun.
To remove the battery from the glue gun, first ensure that
the battery is drained to the point where the battery charge
indicator (8) is lit red. Unscrew the screws on the housing
and remove the housing shell in order to remove the battery.
To prevent a short circuit, disconnect the connectors on the
battery one at a time and then isolate the poles. Even when
fully discharged, the battery still contains a residual capacity
which can be released in case of a short circuit.
Bosch Power Tools