Starting Operation; Working Advice - Bosch PKP 3,6 LI Notice Originale

10 | English
Cordless glue gun
Rated voltage
Capacity
Number of battery cells
Operating time per battery
charge approx. (according
to Bosch testing procedures)
A) Limited performance at temperatures <0 °C
B) Corresponds to approx. six glue sticks
Power supply
Article number
Output voltage
Output current
Permitted battery temperat-
ure during charging
Charging time
Protection class
Additional technical data can be found at:
http://www.bosch-do-it.com/ecodesign
Assembly
Battery Charging (see figure A)
Use only the power supplies listed in the technical
u
data. Only these power supplies are matched to the lith-
ium-ion battery of your glue gun.
Pay attention to the mains voltage. The voltage of the
u
power source must match the voltage specified on the
rating plate of the power adaptor. Power adaptors
marked with 230 V can also be operated with 220 V.
Note: The battery is supplied partially charged. To ensure
full capacity of the battery, completely charge the battery
before the first use.
The lithium-ion battery can be charged at any time without
reducing its service life. Interrupting the charging process
does not damage the battery.
The Li-ion battery is protected against deep discharge. A
protective circuit switches the glue gun off when the battery
is drained, meaning the adhesive is no longer being heated.
If the battery charge indicator (8) flashes red, the battery
has less than 30% capacity and should be charged. When
the battery is fully charged, the battery charge indicator is
continuously lit red.
To charge the battery, connect the Micro-USB con-
nector (10) of the charging cable (11) to the charging
socket (9) and the USB charging connector (12) to the
power supply (13). Then plug the mains plug of the power
supply into the plug socket.
The battery charge indicator (8) will flash green during the
charging process. When the charging process is complete,
the battery charge indicator will be continuously lit green.
Unplug the power supply from the mains.
1 609 92A 5TJ | (23.07.2020)
The glue gun cannot be used during the charging process.
PKP 3,6 LI
The lack of function during the charging process does not
V= 3.6
mean that the tool is defective.
Ah 1.5
Protect the power adaptor against moisture!
u
1
B)
min 30
Operation

Starting Operation

Switching On and Off
To switch on the glue gun, press and hold the on/off but-
ton (7) until the heating indicator (6) lights up green.
The heating indicator (6) will flash while the tool is heating
2 609 120 7..
up. Once it is continuously lit, the glue gun is ready to use.
V 5.0
To switch off the glue gun, press and hold the on/off but-
A 1.0
ton (7) until the heating indicator (6) goes out.
°C +5 to +40
Note: If the glue gun is not used for longer than five minutes,
it will switch off automatically to save energy.
h 3−4
When switching on again, check the battery charge indic-
ator (8): If it lights up red, the battery needs to be charged.
/Ⅱ
Safely place the glue gun down after use and let it cool
u
completely before packing it away. The hot nozzle can
cause damage.

Working Advice

Keep people and animals away from the hot adhesive
u
and the nozzle tip. Adhesive and nozzle tip will heat up to
170 °C, posing a risk of burns. If hot adhesive comes into
contact with skin, immediately hold the affected area un-
der a stream of cold water for several minutes. Do not try
to remove the hot adhesive from the skin.
Only use adhesives that have been recommended by the
manufacturer of the glue gun.
Adhesive bonds can become unstuck when they are affected
by moisture.
Preparing for gluing
The bonding locations must be clean, dry and free from
grease.
The materials to be glued together and the work surface
must not be easily ignited or flammable.
Test whether heat-sensitive materials are suitable before-
hand on a sample workpiece.
The ambient temperature and the workpieces to be glued
must not be colder than +5 °C and not warmer than +50 °C.
Materials that cool the adhesive down quickly should be
warmed first with a hot air gun.
Gluing
Push the glue stick (4) suited to the material into the glue
stick compartment (5).
Switch on the glue gun and allow it to heat up. The heating
indicator (6) will flash during heating.
Once the heating indicator (6) is continuously lit, the glue
gun is ready to use.
Apply moderate pressure to the feed trigger (3).
Bosch Power Tools