Important; Cleaning, Maintenance And Ordering Of Spare Parts - EINHELL HEROCCO Instructions D'origine

6.2 Drill / Impact drill / Chisel selector switch
(Fig. 8)
•
For drilling, press the button (E) on the rotary
switch (2) and simultaneously turn the rotary
switch (2) to position A.
•
For impact drilling, press the button (E) on the
rotary switch (2) and simultaneously turn the
rotary switch (2) to position B.
•
For chiseling, press the button (E) on the
rotary switch (2) and simultaneously turn the
rotary switch (2) to position C.
•
In switch position C the chisel is not locked.
•
For chiseling, press the button (E) on the
rotary switch (2) and simultaneously turn the
rotary switch (2) to position D.
•
The chisel is locked in position D.

Important!

You need apply only slight contact pressure for
impact drilling. Excessive contact pressure will
place unnecessary strain on the motor. Check drill
bits at regular intervals. Sharpen or replace blunt
drill bits.
6.3 Changeover switch (Fig. 9)
Using the changeover switch (3) above the On/Off
switch (4) you can select the direction of rotation
of the equipment and lock the equipment so that
it cannot be switched on accidentally. You can
select between clockwise and counter-clockwise
rotation. To avoid causing damage to the gearing,
the direction of rotation must only be changed
when the equipment is at a standstill. When the
changeover switch (3) is in the middle position,
the On/Off switch (4) is blocked.
Danger!
To avoid danger, the machine must only be held
using the two handles.
Otherwise you may suff er an electric shock if you
drill into electric cables!
6.4 On/Off switch (Fig. 9)
Infi nitely variable speed control is possible with
the On/Off switch (4). The further you push the
switch, the higher the speed of the equipment.
Switching on:
Press the On/Off switch (4).
Switching off :
Release the On/Off switch (4).
Anl_Herocco_4513975_SPK7.indb 24 Anl_Herocco_4513975_SPK7.indb 24
GB
6.5 Battery capacity indicator (Fig. 10)
Press the button for the battery capacity indicator
(d). The battery capacity indicator (7) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED blinks:
The battery is empty, recharge the battery.
All LEDs blink:
The battery pack has undergone exhaustive
discharge and is defective. Do not use or charge
a defective battery pack.
6.6 LED light (Fig. 1)
The LED light (9) can be used in poor lighting
conditions to illuminate the area where you want
to drill or screw. The LED light (9) will come on
automatically as soon as you press the On/Off
switch (4).
6.7 screws
It is advisable to use self-centering screws (e.g.
Torx, cross recessed head) as these will enable
you to work safely and reliably. Always make sure
that the bit used is of the same size and shape as
the screw.
7. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
7.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
- 24 -
21.10.2020 15:54:36 21.10.2020 15:54:36