Dust/Chip Extraction - Bosch GWX 18V-10 Professional Notice Originale

26 | English
chine head carefully, without removing it from the hous-
ing, into the new position. Screw in and retighten the four
screws.

Dust/Chip Extraction

The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
terial wherever possible.
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
Avoid dust accumulation at the workplace. Dust can
u
easily ignite.
Operation
Start-up
Inserting the battery
Push the charged battery (8) into the base of the power tool
from the front until the battery is securely locked.
Speed preselection
GWX 18V-10 SC
You can use the button for speed preselection (27) to preselect the required speed, even during operation. The information in
the table below describes the recommended values.
Material Application
Metal Brushing, removing rust
Stainless steel Grinding
Metal Rough grinding
Metal Cutting
1 609 92A 5JY | (03.12.2019)
The machine head can be
rotated in 90° increments.
In this way, the on/off
switch can be brought into
a more favourable handling
position for particular ap-
plications, e.g. for left-
handed tool users.
Completely unscrew the
four screws. Rotate the ma-
Application tool
Cup brush
Fibre disc
Grinding disc
Cutting disc
Switching on/off
To start the power tool, push the on/off switch (6) forward.
To lock the on/off switch (6) in position, push the on/off
switch (6) forward and down until it clicks into place.
To switch off the power tool, release the on/off switch (6);
or, if the switch is locked, briefly push the on/off switch (6)
backward and down and then release it.
Always check abrasive tools before using them. The
u
abrasive tool must be fitted properly and be able to
move freely. Carry out a test run for at least one
minute with no load. Do not use abrasive tools that are
damaged, run untrue or vibrate during use. Damaged
abrasive tools can burst apart and cause injuries.
Kickback stop
If there is a sudden kickback in the power tool,
e.g. jamming in a separating cut, the power
supply to the motor will be interrupted elec-
tronically. The LED work light (4) then flashes
white and the status indicator (28) flashes
red.
To restart the tool, set the on/off switch (6) to the off posi-
tion and then switch the power tool on again.
Restart protection
The restart protection feature prevents the power tool from
uncontrolled starting after the power supply to it has been
interrupted.
When restart protection is activated, the status indicator
(28) flashes red.
To restart the tool, set the on/off switch (6) to the off posi-
tion and then switch the power tool on again.
Impact shutdown
The integrated impact shutdown switches the power tool off
as soon as it hits the floor. The status indicator (28) then
flashes red. To restart the tool, set the on/off switch (6) to
the off position and then switch the power tool on again.
User interface (see figure B)
The user interface (5) is used to preselect the speed and to
indicate the status of the power tool.
Speed preselection
level
1
2
3
3
GWX 18V-10 SC
(125 mm)
-1
[min ]
4500
6000
9000
9000
Bosch Power Tools