Before You Send In The Appliance; Technical Data - Dirt Devil CENTRINO cleancontrol 3.0 M2992-0 Mode D'emploi

4 Troubleshooting and technical data

4.1 Before you send in the appliance

4 Troubleshooting and technical data
WARNING:
Danger of injury! Never use a defective appliance! Always switch off the
appliance and disconnect it from the mains before starting troubleshoot-
ing.
Before contacting us or even sending the appliance to us, use the table to
check whether you can correct the problem yourself.
Problem
The cleaning re- The bypass vent (Fig. 5) is open.
sults are unsatis-
Close the bypass vent (Fig. 5).
factory in spite of
The attached nozzle is unsuitable.
the appliance
Change the nozzle,
working correct-
ance and adjust nozzles to surface'.
ly.
The collar brush of the floor nozzle is not in a posi-
tion appropriate to the type of floor (Figures 8 – 9).
Adjust the position of the collar brush to the type of
floor using the floor nozzle switch (Figures 8 – 9).
The dust container is full.
Empty and clean the dust container
'Emptying and cleaning the dust container'.
The filters are dirty.
Clean the filters,
cleaning the dust container' that is
'Cleaning / changing the exhaust filter'.
Nozzle, telescopic tube or suction hose is blocked.
Remove the obstruction. If necessary, use a long
wooden stick (e.g. a broomstick) to do this.
4.2 Warranty
The statutory warranty regulations in accordance with the EU Directive
1999/44/EC apply.
4.3 Disposal
Dispose of the appliance in compliance with the environmental
protection laws of your country. Electrical waste may not be dis-
posed of together with domestic waste. Use local old-appliance
collection points instead.

4.4 Technical data

Type of appliance
Model name
Model number
Voltage
Power
Max. available dust container
capacity
Power cord length
Weight
Possible cause / solution
Chapter 2.1, 'Assemble appli-
Chapter 3.1,
Chapter 3.1, 'Emptying and
Chapter 3.2,
: bagless cylinder vacuum cleaner
: Centrino Cleancontrol 3.0
: M2992 (-0/-1/.../-8/-9)
: 220-240 V ~, 50/60 Hz
: 1,000 W
: approx. 1.6 litres
: approx. 5 m
: approx. 3.5 kg
Technical and design specifications
may be changed in the course of contin-
uous product improvement.
© Royal Appliance International GmbH
Problem
Cleaning / emp- The dust container is full.
tying display
Empty and clean the dust container
lights up (Fig.
'Emptying and cleaning the dust container'.
16).
The filters are dirty.
Clean the filters,
cleaning the dust container' or
'Cleaning / changing the exhaust filter'.
Nozzle, telescopic tube or suction hose is blocked.
Remove the obstruction. If necessary, use a long
wooden stick (e.g. a broomstick) to do this.
The vacuum The overheating protection has tripped (possibly
cleaner stops due to blocked suction channels, filters, or similar).
suddenly. 1. Switch the appliance off and pull the plug out of
the socket.
2. Remove the cause of overheating (e.g. by dis-
assembling telescopic tube and suction hose
and removing the obstacle and/or cleaning fil-
ters).
3. Wait approx. 45 minutes until the appliance has
cooled off.
4. After the appliance has cooled off, you may
switch it on again.
NOTE:
If you cannot solve the problem following these instructions, contact our
customer services ( Page 46, 'International Service').
In non-EU countries the minimum requirements of the warranty in the re-
spective country apply.
The filters are made from environment-friendly materials. You can dispose
of these — as opposed to the appliance — in your domestic waste unless
you have cleaned up substances that are prohibited from disposal in this
way.
Possible cause / solution
Chapter 3.1,
Chapter 3.1, 'Emptying and
Chapter 3.2,
15