Cleaning The Exhaust Filter; Spare Parts And Accessories; Before You Send In The Appliance - Dirt Devil Magnum PR Mode D'emploi

5 Maintenance
1
13

5.3 Cleaning the exhaust filter

ATTENTION:
The filter is washable, but it may not be cleaned in dishwashers or wash-
ing machines. Also, do not use detergents or brushes with hard bristles
to clean the filter. Let the filter dry for approx. 24 hours at room tempera-
ture after washing it. Only put it back in place when it is completely dry.
14

5.4 Spare parts and accessories

ATTENTION:
Only use original spare parts from the scope of delivery or those that you
have purchased by reordering.
„ Ordering address: ZPage 48, "International Service"
„ Further information: Z www.dirtdevil.de

5.5 Before you send in the appliance

Before contacting us or sending the appliance to us, use the following table
to check whether you can correct the problem yourself.
NOTE:
If you cannot solve the problem following these instructions, contact the
Royal Appliance customer service (ZPage 48, "International Service").
Problem Possible cause / solution
The vacuum The overheating protection has tripped (possibly due to
cleaner blocked suction channels, filters, or similar).
stops sud- Switch the appliance off and pull the plug out of the socket.
denly. Remove the cause of overheating (e.g. by disassembling
telescopic tube and suction hose and removing the obsta-
cle and/or cleaning filters).
Wait for about 45 minutes.
After the appliance has cooled off, you may switch it on
again.
Cleaning in- The central lamellae filter is dirty.
Clean the central lamellae filter, ZChapter 5.2, "Cleaning
dicator
(Fig. 1/2) central lamellae filter and motor protection filter".
lights up.
The dust container is full.
Empty/clean the dust container. ZChapter 5.1, "Emptying
and cleaning the dust container"
A B
A B
11. Put the filter screen onto the bottom side of the cover in such a way that
the tab engages the notch next to the spring (Fig. 13/A1) as shown.
12. Turn the filter screen securely in the 'LOCK' direction (Fig. 13/A). You
will feel and hear the filter screen snap into place.
NOTE:
If you also have a filter fleece (optional), slide the filter fleece back onto
the filter screen until it completely covers its mesh.
13. Put the cover back onto the dust container. Make sure when replacing it
that the arrow on the cover is exactly above the 'open' marking on the dust
container. Fix the cover by twisting it in the 'close' direction (Fig. 13/B).
14. Place the dust container back into its holder and close the housing cov-
er. The release buttons must click shut audibly. Check that the housing
cover is fitted securely.
„
It is best to clean the exhaust filter every third time that the central la-
mellae filter is cleaned.
„
However, clean the exhaust filter at least every six months.
1. Switch off the appliance, ZChapter 4.3, "Switching off".
2. Push the release catch of the exhaust filter cover down (Fig. 14/A) and
open out the exhaust filter cover.
3. Remove the exhaust filter (Fig. 14/B).
4. Tap the dirt out of the exhaust filter over a dustbin.
5. Should this be insufficient, clean the the filter with a soft brush, e. g. the
furniture brush supplied with the appliance.
6. If this dry cleaning is still insufficient, then rinse the filter in clear cold
water.
7. If the exhaust filter is damaged, replace it (order information ZChapter
5.4, "Spare parts and accessories").
8. Place the clean/new exhaust filter back into its receptacle (Fig. 14/B).
9. Fit the exhaust filter cover on the bottom side first (Fig. 14/A) and then
hinge it upwards.
„
The following accessories and spare parts can be reordered:
Item number Description
3883001 4-piece filter set
(1 central lamellae
filter, 1 motor pro-
tection filter, 2 filter
fleeces)
Problem Possible cause / solution
The clean- The bypass vent (Fig. 1/17) is open.
ing results Close the bypass vent.
are unsatis-
The attached nozzle is unsuitable.
factory in
Change the nozzle, ZChapter 3.2, "Selecting the proper
spite of the
nozzle".
appliance
The suction power you set is unsuitable.
working cor-
Adjust the suction power control to suit the flooring,
rectly.
ZChapter 4.2, "Vacuum cleaning", step 4.
The position of the 'carpet/hard floor' selector (Fig. 1/9) is
unsuitable. Set the 'carpet/hard floor' selector to the cor-
rect position for the type of floor, ZChapter 4.2, "Vacuum
cleaning", step 5.
The dust container is full. Clean the dust container
ZChapter 5.1, "Emptying and cleaning the dust container".
The filters are dirty. Clean the respective filter ZChapter
5.2, "Cleaning central lamellae filter and motor protection
filter" or ZChapter 5.3, "Cleaning the exhaust filter".
Nozzle, telescopic tube or suction hose is blocked.
Remove the obstacle. If necessary, use a long wooden
stick (e.g. a broomstick) to do this.
Item number Description
3883002 1 exhaust filter
3883077 2 filter fleeces
M203 1 parquet brush
M209 1 turbo brush
15