Klein Tools MM200 Manuel D'instructions

ENGLISH
6. Capacitance < 200μF
H z%
Temp
µA
mA
A
H
z%
Temp
Temp
m
COM
600V MAX
10A/250V ~ 400mA/250V ~
• Safely discharge capacitor before measurement.
• Reading may take up to 60 seconds for large capacitors.
7. Frequency (Hz)/duty Cycle < 1MHz
PRESS
H
z%
Temp
µA H
z%
mA
Hz %
A
• Follow AC Voltage test setup.
≤ ≤
8. Temperature: -4° °F 1832°
H z%
Temp
µA
H
z%
mA
A
Temp
µA
Temp
m
COM
600V MAX
10A/250V ~ 400mA/250V ~
mA
A
• Use included thermocouple and adapter.
• Do not apply voltage to thermocouple.
SyMBOLS USEd ON LCd
~
aC Measurement dC Measurement
-
OL
Negative dC Value Overload: Range Exceeded
H
Low Battery Hold active
V
AUTO auto Range active Voltage Measurement
%
duty Cycle Mode Frequency Mode
A Ω
Current in amps Resistance in Ohms
diode Test Continuity Test
n F
Nano 10 ° Temperature in Fahrenheit
-9
m F
Milli 10 -3 Capacitance in Farads
µ M
Micro 10 -6 Mega 10 6
k
Kilo 10 3
ELECTRICaL SPECIFICaTIONS
dC Voltage Measurement
Range Resolution accuracy
400mV ~ 600V 0.1mV ~ 1V ± (0.5% + 3 digits)
Overload Protection: 600V RMS Input Impedance: > 10MΩ.
MM200-Instructions-139572TART.indd 1-4
Downloaded from www.Manualslib.com
aC Voltage Measurement
Range Resolution accuracy
4V ~ 600V 1mV ~ 1V ± (1.2% + 5 digits)
Overload Protection: 600V RMS Frequency: 50 ~ 60Hz
Input Impedance: > 10MΩ Response: Averaging
aC/dC Current Measurement
Range Resolution dC accuracy
400μA ~ 400mA 0.1μA ~ 0.1mA ± (1.0% + 3 d)
10A 0.01A ± (3.0% + 5 d)
Overload Protection: Max Input Current:
ma Input: F400mA / 250V fuse ma Input:
• •
10a Input: F10A / 500V fuse 10a Input:
• •
Resistance Measurement
Range Resolution accuracy
400Ω ~ 4MΩ 0.1Ω ~ 0.001MΩ ± (0.8% + 4 digits)
40MΩ 0.01MΩ ± (1.5% + 4 digits)
Overload Protection: 600V RMS
Capacitance Measurement
Range Resolution accuracy
4nF ~ 40μF 0.001nF ~ 0.01μF ± (3.0% + 6 digits)
200μF 0.1μF ± (4.0% + 6 digits)
Overload Protection: 600V RMS
Stated accuracy with film capacitor or better.
4nF Range:
Frequency Measurement
Range Resolution accuracy
9.999Hz ~ 999.9kHz 0.001Hz ~ 0.1kHz ± (0.5% + 2 digits)
Overload Protection: 600V RMS
Sensitivity: 0.7V RMS at 1MHz
Temperature Measurement
Range Resolution accuracy
-4°F ~ 32°F 1°F ± (5.0% + 2 digits)
32°F ~ 1832°F 1°F ± (3.0% + 2 digits)
Overload Protection: 600V RMS
Sensor: K-type thermocouple, accuracy not listed
duty Cycle Measurement
Range Resolution accuracy
0.1% ~ 99.9% 0.1% ± (2% + 5 digits)
Overload Protection: 600V RMS
Frequency: 0.5Hz ~ 100kHz (pulsewidth > 2μsec)
Designer/Production: Sandra ex 15612
Client Contact: Chris Trott, ex 13267
Client Sign off:
manuals search engine
diode Test
Overload Protection Test Current
600V RMS Appx. 0.6mA
Continuity Test
Overload Protection
600V RMS
aC accuracy
WaRRaNTy
± (1.2% + 3 d)
This product is warranted to be free from defects in materials and workmanship
± (3.0% + 5 d)
for a period of two years from the date of purchase. During this warranty period,
Klein Tools has the option to repair or replace or refund the purchase price of
400mA DC / AC RMS any unit which fails to conform to this warranty under normal use and service.
10A DC / AC RMS This warranty does not cover damage which occurs in shipment or failure which
results from alteration, tampering, accident, misuse, abuse, neglect, or improper
maintenance. Batteries and damage resulting from failed batteries are not
covered by warranty. A purchase receipt or other proof of original purchase date
will be required before warranty repairs will be rendered.
Any implied warranties, including but not limited to implied warranties of
merchantability and fitness for a particular purpose, are limited to the express
warranty. Klein Tools shall not be liable for loss of use of the instrument or other
incidental or consequential damages, expenses, or economic loss, or for any
claim or claims for such damage, expenses or economic loss.
Some states or countries laws vary, so the above limitations or exclusions may
not apply to you. This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. If your Klein product requires
repair or for information on how to exercise your rights under the terms of this
warranty, please contact Klein Tools at 1-877-775-5346.
CLEaNING
Turn instrument off and disconnect test leads. Clean the instrument by using
a damp cloth. Do not use abrasive cleaners or solvents.
STORaGE
Remove the batteries when instrument is not in use for a prolonged period of
time. Do not expose to high temperatures or humidity. After a period of storage
in extreme conditions exceeding the limits mentioned in the Specifications
section, allow the instrument to return to normal operating conditions before
using it.
dISPOSaL / RECyCLE
Caution:
This symbol indicates that equipment and its accessories
shall be subject to a separate collection and correct disposal.
CUSTOMER SERVICE
KLEIN TOOLS, INC.
450 Bond Street
Lincolnshire, IL 60069
1-877-775-5346
www.kleintools.com
Rev. 06/10
Instruction Instruction
Manual Manual
Open Circuit Voltage
Appx. < 1.5V DC
MM200
Open Circuit Voltage
Appx. 0.44V
ENGLISH
• BaCKLIGHT
• KICK STaNd
• LEad
HOLdER
• aUTO
RaNGING
• daTa HOLd
• 3-3/4 dIGIT
3999 COUNT
LCd
www.kleintools.com
139572T
FIle Name: MKT121707-MM200-Multimeters-139572TART
Product: MM200
Package Part #: 139572T
Date: 4/06/10
MM200
FUNC. HOLD H
z%
H
z%
Temp
µA
mA
A
Temp
m
COM
CATIII
600V MAX
~ ~
10A/500V
400mA/250V
6/3/10 8:41 AM