Bluetooth Audio; Sleep Function; Clock Setup - LENCO DAR-045 Mode D'emploi

BLUETOOTH AUDIO

Please follow the pairing instructions below to link the unit to your Bluetooth device.
1. Press the SOURCE button repeatedly to enter the Bluetooth mode. The display will show "BT". It will start searching and will
display a flashing "PAIRING".
2. If the unit has never been paired with a Bluetooth device before or cannot find the last paired device, the display and the
Bluetooth status indicator will keep on flashing. Turn on the Bluetooth function of your device and enable the search until "Lenco
DAR-045" is found. Select "Lenco DAR-045" on the Bluetooth device to make connection. Enter the pass code "0000" if required.
3. After successfully paired the unit will display steady "BT AUDIO".
4. You can now start playing music from your smartphone wirelessly to the speaker.
5. You can press the BT PLAY/PAUSE
6. You can press the BT PREVIOUS

Press and hold the
device.
AUX IN
This allows you to connect the sound from an external player through your unit.
1. Plug a 3.5mm audio cable (not included) into your external player line out and the other end into the AUDIO IN jack.
2. Press the SOURCE button to enter AUX mode. Display shows "AUX".
3. Start your external player to play music.
4. The unit plays the sound.
EQ OPERATION/X-BASS
You can enjoy different EQ sound effect modes. Press the EQUALIZER button to go to different sound effects from
FLAT/ROCK/CLASSIC/POP/JAZZ.
You can also boost the bass effect of the music. Press the X-BASS button will toggle the X-Bass effect between On and Off.
Note:
When X-Bass is enabled, the EQ sound effect will be disabled. Pressing EQUALIZER button will only show BASS ON without any
-
EQ effect. To resume the EQ sound effect, press the X-BASS button to turn off first.

SLEEP FUNCTION

1. When the unit is switched on, press the SLEEP button repeatedly to select a sleep duration from either SLEEP 00 (Off), 90, 80, 70,
60, 50, 40, 30, 20 or 10 minutes.
2. When the sleep timer is zero, the unit will turn off automatically.
3. To cancel the sleep function, press the STANDBY button to turn off the unit. Or press the SLEEP button repeatedly to select
"SLEEP 00".

CLOCK SETUP

1. Turn off the unit in Standby mode.
2. Press the CLOCK SET button to set the clock. It will display "24H".
3. Press the PREVIOUS
ENTER button on the remote) to confirm.
4. Press the PREVIOUS
confirm.
5. Press the PREVIOUS
finish the clock set.
Note:
The time set may automatically be overriden by the DAB+ or FM station real time information.
-
When the unit is turned on, pressing the CLOCK SET button will display the time on the display for a few seconds.
-
TIMER ON/OFF SETUP
1. Turn off the unit in Standby mode.
2. Press and hold the TIMER button to set the timer on/off. It will display "ONCE" with a flashing symbol
3. Press the PREVIOUS
4. It will display "TIME ON" for a moment. Then while it displays the flashing hour digits, press the PREVIOUS
button to set the on timer hour value. Press the ENTER button to confirm.
5. Then it displays the flashing minute digits. Press the PREVIOUS
the ENTER button to confirm.
6. It will display "TIME OFF" for a moment. Then while it displays the flashing hour digits, press the PREVIOUS
button to set the off timer hour value. Press the ENTER button to confirm.
7. Then it displays the flashing minute digits. Press the PREVIOUS
the ENTER button to confirm.
button to pause or resume the playback.
or BT NEXT
button on the unit will disconnect the current connection and start to search another new Bluetooth
or NEXT button to adjust the hour display format between 24H or 12H. Press the SELECT button (or
or NEXT button to adjust the hour. Press the SELECT button (or ENTER button on the remote) to
or NEXT button to adjust the minute. Press the SELECT button (or ENTER button on the remote) to
or NEXT button to toggle between "ONCE and "DAILY". Press the ENTER button to confirm.
button to search to the previous or next song.
or NEXT
or NEXT
12
.
button to set the on timer minute value. Press
button to set the off timer minute value. Press
or NEXT
or NEXT