Rational Combi-Duo 10x2/1 GN Manuel D'installation page 12

This Combi-Duo kit can only be used for units
produced after 12/97.
If you wish to use a unit produced before 12/97 as a
bottom unit, please contact us and let us know the
unit serial number.
The Combi-Duo kit 10x2/1 GN Electric (spare part no.
(see page 3) consists of:
Pos. Pcs. Spare part no. Description
1 1 6021.1334
2 4 2039.0114
3 2 6021.1348
4 1 2765.1339
- 3 2039.0353
- 1 5006.0200
The Combi-Duo CleanJet
see page 8, consists of the following parts:
Pos. Pcs. Spare part no. Description
5 1 8664.1368
6 1 6021.1550
7 1 6021.1553
8 1 6021.1512
9 1 6021.1554
10 2 2062.0338
11 4 2066.0516
- 1 4005.0101
- 8 1204.0120
- 8 1004.0666
- 4 2066.0533
GB
12
Cover stiffening plate
Upper foot part 135 mm
Ventilation pipe
Fixing bracket for ventilation pipe
Silicone plugs
Tube of silicone paste
® accessory set (6008.1314),
Suction hose set
Hose set complete
Hose guide 102 bottom
Hose guide 102 rear
Hose guide 102 cover
Plastic Y-joint
Hose clamp 60-80 mm
Cable tie
A 4.3 tooth lock washer
M4 x 10 hexagon screw
Hose clip
Bottom unit, 10x2/1 GN Elektro:
• For CleanJet ® units:
a) Pull out cleaning agent/rinse aid tank until it stops
b) Remove connector hoses from the cleaning agent/rinse
aid tank.
c) Remove tank from unit.
- Unscrew the lower part of the foot of the unit
- Unscrew the upper part of the foot of the unit using a
17 mm open-ended wrench
- Use a M10x30 screw to fit the new upper foot part
(pos. 2, length 135 mm) to the unit
- Screw in the lower part of the foot of the unit.
• For units with CleanJet
a) fix the hose set complete (pos. 6) with two hose clamps
to top of foot, front left,
b) fix the hose guide 102 bottom (pos. 7) with two hose
clamps to top of foot, rear left,
• If the upper unit is also to be fitted with CleanJet
proceed as follows:
a) Cut the two suction hoses of the complete connector set
(pos. 6) approx. 200 mm behind the connectors.
b) Remove the elbow joints of the unit's connector hoses.
c) Connect the connector hoses of the unit and hoses of
the complete connector set using the Y-joint.
d) Also attach the cut-away hoses of the complete
connector set (used for connecting to the upper unit) to
the Y-joint
e) Fix hoses with cable ties to the floor
f) Position rear hose guide 102 (pos. 8) in place on
ventilation pipe and using M4x10 screws, screw to
bottom hose guide 102 (pos. 7)
• If the upper unit is not to be fitted with CleanJet
the connector hoses of the complete connector set can be
fitted direct to the pumps. Hoses must then be shortened to
the appropriate length.
- Position the unit and align it using a spirit level
- Remove the dome
- Remove the door holding plate and take off the door
- Clean the cover surface thoroughly.
- Using silicone paste, spread a bead around the holes in the
unit cover
- Place the cover stiffening plate (pos. 1) in position
- Refit the dome again with the distance piece
- Refit the door and the door holding bracket
- Adjust the door
pic. 1
pic. 2
® :
page 8/9 "A"
page 8/9 "C"
page 8/9 "B"
page 8/9 "D"
pic. 3
pic. 4
pic. 5
pic. 6
pic. 7
Duo 102E/61 Md 05/02
® ,
®