Ryobi BIW180 Manuel D'utilisation page 5

Table des Matières

Publicité

Les langues disponibles
  • FR

Les langues disponibles

  • FRANÇAIS, page 7
GB
FR
DE
ES
OPERATION
BATTERY PROTECTION FEATURES
Ryobi 18 V lithium-ion batteries are designed with
features that protect the lithium-ion cells and maximize
battery life. Under some operating conditions, these
built-in features may cause the battery and the tool
it is powering to act differ-ently from nickel-cadmium
batteries.
During some applications, the battery electronics may
signal the battery to shut down, and cause the tool to
stop running. To reset the battery and tool, release the
trigger and resume normal operation.
NOTE: To prevent further shut down of the battery, avoid
forcing the tool.
If releasing the trigger does not reset the battery and
tool, the battery pack is depleted. If depleted, the battery
pack will begin charging when placed on the lithium-ion
charger.
TO INSTALL BATTERY PACK
See Figure 2.
Q
Place the rotation selector in the center position.
Q
Insert the battery pack into the product as shown.
Q
Make sure the latches on each side of the battery
pack snap in place and that battery pack is secured in
the product before beginning operation.
TO REMOVE BATTERY PACK
Q
Depress the latches on each side of the battery pack.
Q
Remove the battery pack from the impact wrench.
WARNING
Battery products are always in operating
condition. Therefore, the switch should always be
locked when not in use or carrying at your side.
CAUTION
The metal surface may become hot during use.
Avoid contact with it to avoid possible burn injury.
SWITCH TRIGGER
See Figure 3.
To turn the impact wrench ON, depress the switch trigger.
To turn it OFF, release the switch trigger.
The switch trigger can be locked in the OFF (center)
position. This feature can be used to prevent the
possibility of accidental starting when not in use. To lock
switch trigger, place the direction of rotation selector in
center position.
VARIABLE SPEED
The variable speed switch trigger delivers higher speed
IT
NL
PT
DK
SE
FI
NO
RU
PL
CZ
English
with increased trigger pressure and lower speed with
decreased trigger pressure.
NOTE: You might hear a whistling or ringing noise from
the switch during use. Do not be concerned; this is a
normal part of the switch function.
ROTATION SELECTOR
(FORWARD/REVERSE/CENTER LOCK) (see Figure 3.)
The direction of bit rotation is reversible and is controlled
by a selector located above the switch trigger. With the
drill held in normal operating position, the direction of
rotation selector should be positioned to the left of the
switch trigger for forward drilling. The drilling direction is
reversed when the selector is to the right of the switch
trigger.
Setting the switch trigger in the OFF (center lock) position
helps reduce the possibility of accidental starting when
not in use.
CAUTION:
To prevent gear damage, always allow the chuck
to come to a complete stop before changing the
direction of rotation.
To stop, release switch trigger and allow the coupler to
come to a complete stop..
WARNING
Make sure the bit is secured in the coupler
before using the impact driver. Failure to do so
could cause serious personal injury.
WARNING
Do not drive a screw where there is likely to be
hidden wiring behind the surface. Contact with
a "live" wire will make exposed metal parts of
the tool "live" and shock the operator. If you
must drive a screw where hidden wire may be
present, always hold tool by insulated gripping
surfaces (handle) when performing the operation
to prevent a shock to the operator, as seen in
figure 5.
CAUTION:
The impact driver is not designed to be used as a
drill.
INSTALLING AND REMOVING SOCKETS
See Figures 4.
Use only sockets designed for impact wrenches. Always
select the correct size impact socket for nuts and bolts.
Using the wrong size socket may damage the nut or
bolt and cause the fastening torque to be inaccurate or
inconsistent.
Q
Remove the battery pack.
2
HU
RO
LV
LT
EE
HR
SI
SK
GR
TR

Publicité

Table des Matières
loading

Table des Matières