Manual Settings - Hama EWS Intro Mode D'emploi

Note
• The respective symbols will ash during the connection
attempts: connection to the measuring station,
connection to the DCF signal
• Do not press any buttons during setup. Otherwise, values
may not be transmitted correctly and there is a risk of value
errors and inaccuracies.
• Do not change the location of the base station during the
search processes.
• The process is completed when the indoor (17) and outdoor
(13) measurement data is displayed.
6.2 Basic and manual settings
Automatic setting using the DCF signal
When the base station has been switched on for the rst time and
successful transmission has been established between the base
station and the measuring station, the clock will automatically
search for the DCF signal. During the search, the radio symbol
ashes.
Display
Flashing display
Constant display
No display
• If the station still does not receive a signal, press and hold the
Z/Register button (23) for approximately 3 seconds to start
the manual search for the DCF signal. The DCF radio symbol (3)
begins to ash.
Note – Time settings
• The search process can take up to 10 minutes. If the search
fails, it ends and is repeated at the next clock hour. The DCF
radio symbol (3) goes out.
• In the meantime, however, you can set the time and the
date manually.
• The clock automatically continues to search for the DCF
signal on a daily basis (between 2 am and 4 am and between
5 am and 6 am). If the signal is received successfully, the
manually set time and date are overwritten.
Note – Summer time
The clock automatically switches to summer time.
appears on the display as long as summer time is activated.

Manual settings

• Press and hold the CLOCK button (21) for approximately 3
seconds to make the following settings one after the other:
• 12 or 24-hour format
• Weekday language (GE = German, FR = French,
ES = Spanish, IT = Italian, EN = English)
• Time zone (from -12 to +12 hours CET)
4
Search for the DCF signal
Active
Successful –
signal is being received
Inactive
• Hour
• Minute
• Second
• Year
• Month
• Day
Press the SET/RESET button (25) to select your setting. Press the
CLOCK button (21) to con rm your entries.
Note – Time zone
• The DCF signal can be received over long distances, but
always transmits the current Central European Time in
Germany. Make sure you account for the time difference in
countries in other time zones.
• If you are in Moscow, the time is 3 hours later than in
Germany. This means that you should set +3 for the time
zone. The clock then sets the time automatically to 3 hours
ahead after receiving the DCF signal or according to the
manually set time.
Alarm
• Press and hold the ALARM button (22) for approximately 3
seconds to set the time of the alarm displayed. The hours display
begins to ash.
• Press the SET/RESET button (25) to select the hour for the
alarm time and con rm your selection by pressing the ALARM
button (22). The minutes display begins to ash.
• Repeat the process to set the minutes for the alarm time.
• Repeat the entire process to set the second alarm.
• If you do not make an entry for 25 seconds, you automatically
exit the setting mode.
• Press the ALARM button (22) once to display the rst alarm
time. Press the ALARM button (22) once more to display the
second alarm time.
• Press the SET/RESET button (25) once to activate the rst
alarm. Press the SET/RESET button (25) once more to activate
the second alarm. Press the SET/RESET button (25) a third time
to activate both alarms.
• An activated alarm is indicated by the respective symbol
/ on the display.
1
2
• Press the SET/RESET button (25) repeatedly to deactivate the
daily alarm. The alarm symbol
• If the alarm is triggered, the alarm symbol is displayed and an
alarm will sound.
• Press SELECT (24), SET/RESET (25), ALARM (22) or CLOCK
(21) to stop the alarm. Otherwise, it will stop automatically
after 2 minutes.
Note – Snooze function
• While the alarm is sounding, press the Z/Register button
(23) to activate the snooze function. The snooze symbol
and alarm symbol
1
The alarm signal will stop for approximately 5 minutes, after
which it will sound again.
• Press the SELECT button (24) to stop the snooze function
and the alarm.
/ is not displayed.
1
2
begin to ash on the display.
/
2
z
Z