Indesit IN2IFC14BN6 Guide De Référence page 8

TROUBLESHOOTING
In case your dishwasher doesn't work properly, check if the problem can be solved by going through the following list.
For other errors or issues please contact authorized After-sales Service which contact details can be found in the warranty booklet.
Spare parts will be available for a period of either up to 7 or up to 10 years, according to the specific Regulation requirements.
PROBLEMS POSSIBLE CAUSES
Salt indicator Salt reservoir is empty. (After refill the salt indi-
is lit cator may remain lit for several wash cycles).
Rinse aid Rinse aid dispenser is empty. (After refill the rinse
aid indicator may remain lit for several wash cycles). Refill dispenser with rinse aid (for more information - see page 2).
indicator is lit
The appliance has not been plugged in properly. Insert the plug into the socket.
Power outage.
The dishwasher
The dishwasher door is not closed.
won't start or
NaturalDry pin is not pulled in.
does not respond
Cycle is interupted by door opening for more
to commands.
than 4 seconds.
It does not respond to commands.
Display shows: 9 or 12 and On/Off LED is
blinking rapidly
The wash cycle has not finished yet.
The dishwasher
won't drain.
The drain hose is bent.
Display shows:
The sink drain pipe is blocked.
3 and On/Off LED
is blinking rapidly
The filter is clogged up with food residues.
The dishes are rattling against each
The dishwasher
makes excessive
An excessive amount of foam has been pro-
noise.
duced.
The crockery has not been arranged properly.
The spray arms cannot rotate freely, being
hindered by the dishes.
The wash cycle is too gentle.
The dishes are An excessive amount of foam has been produced. The detergent has not been measured out correctly or it is not suitable for
not clean.
The cap on the rinse aid compartment has not
been shut correctly.
The filter is soiled or clogged.
There is no salt.
The dishwasher No water in the water supply or the tap is closed. Make sure there is water in the water supply or the tap running.
does not fill the
The inlet hose is bent.
water.
Display shows: H,
The sieve in the water inlet hose is clogged; it is
6 and On/Off LED
necessary to clean it
is blinking rapidly
Dishwasher
Drain hose positioned too low or siphoning
finishes the cycle
into home sewage system.
prematurely.
Display shows: 15
and On/Off LED is
Air in water supply.
blinking rapidly
Depends on the liquid detergent used and
Detergent leaks. can be emphasized in case of delay option is
activated.
Policies, standard documentation, ordering of spare parts and additional product information can be found by:
• Using QR code on your product.
• Visiting our website docs.indesit.eu and parts-selfservice.europeanappliances.com
• Alternatively, contact our After-sales Service (See phone number in the warranty booklet).
When contacting our After-sales Service, please state the codes provided on your product's identification plate.
The model information can be retrieved using the QR-Code reported in the energy label.
The label also includes the model identifier that can be used to consult the portal of the registry
at https://eprel.ec.europa.eu.
8
SOLUTIONS
Refill reservoir with salt (for more information - see page 2).
Adjust water hardness - see table, page 2.
For safety reasons, dishwasher will not re-start automatically when power
returns. Open dishwasher door, press START/Pause button and close the
door within 4 seconds.
Vigorously push the door until you hear the "click".
Press START/Pause and close the door within 4 seconds.
Switch off the appliance by pressing the ON/OFF button, switch it back
on after approximately one minute and restart the program. If problem
persists, unplug the appliance for 1 minute, then plug it back in.
Wait until the wash cycle finishes.
Check that the drain hose is not bent (see INSTALATION INSTRUCTION).
Clean the sink drain pipe.
Clean the filter (see CLEANING THE FILTER ASSEMBLY).
Position the crockery correctly (see LOADING THE RACKS).
The detergent has not been measured out correctly or it is not suitable
for use in dishwashers (see FILLING THE DETERGENT DISPENSER). Restart
the current cycle by switching OFF the dishwasher, then switch it on
again, select a new program, press START/Pause and close the door with-
in 4 seconds. Please do not add any detergent.
Arrange the crockery correctly (see LOADING THE RACKS).
Arrange the crockery correctly (see LOADING THE RACKS).
Select an appropriate wash cycle (see PROGRAMS TABLE).
use in dishwashers (see FILLING THE DETERGENT DISPENSER).
Make sure the cap of the rinse aid dispenser is closed.
Clean the filter assembly (see CARE AND MAINTENANCE).
Fill the salt reservoir (see FILLING THE SALT RESERVOIR).
Make sure the inlet hose is not bent (see INSTALLATION) reprogram the
dishwasher and reboot.
After having carried out the verification and cleaning, turn off and turn on
the dishwasher and restart a new program.
Check if end of drain hose is placed at correct height (see INSTALLATION).
Check for siphoning into home sewage system, install air admittance
valve if necessary.
Check water supply for leaks or other issues letting air inside.
Small leaks will not cause machine malfunction and can be avoided by
changing liquid detergent type or using tablets.
IEC 436
: