Assembly Of Cover Cl5000Iu 4Cc; Assembly Of Cover Cl5000Il 4C; Install The Rack-Mounted Unit On The Wall; Install The Wall-Mounted Indoor Unit On The Wall - Bosch Climate 5000 M Notice D'installation

▶ Define and mark the position of the suspension bolts on the ceiling.
DANGER
Risk of injury!
The ceiling attachment must be suitable for carrying the weight of the
indoor unit. We recommend using M10 threaded rods in order to be able
to adjust the height precisely. Suitable nuts and washers are included in
the scope of delivery of the indoor unit.
DANGER
Risk of injury!
At least two persons are required to hang the appliance and fasten it
securely.
▶ Do not install the appliance on your own.
▶ Hang the appliance on the suspension bolts with the washers and
nuts included in the scope of delivery.
▶ Position the indoor unit at the correct height and align horizontally by
turning the nuts on the threaded rods.
NOTICE
If the appliance is not level condensate may leak out.
▶ Use a spirit level to align the appliance horizontally.
▶ Secure the appliance at the correct installation position with lock nuts.
▶ Establish pipe connections as described in chapter 4.6.
4.3.2

Assembly of cover CL5000iU 4CC...

▶ Remove the air inlet grille from the cover ( Fig. 107).
▶ Attach cover to the indoor unit with screws provided, paying
attention to orientation ( Fig. 108). The display [2] mst be located
opposite the "shorter" side of the L-shaped electronics [1].
▶ The cover must rest evenly and tightly against the indoor unit.
Only reinstall the air inlet grille when establishing the electrical
connection.
4.3.3

Assembly of cover CL5000iL 4C...

▶ Remove the air inlet grille from the cover ( Fig. 109).
▶ Remove the cover at the 4 corners ( Fig. 110).
NOTICE
Damage to the cover and display
The display is fixed at one of the removable corner covers and can be
damaged when removing the corner.
▶ Carefully lever the corner clamps with a screwdriver and lift off the
corners.
▶ Attach the 4 corner hooks of the cover in the tabs of the indoor unit,
paying attention to the orientation ( Fig. 111). If required, bring
the cover into the correct position by turning it The corner with the
display [2] must be orientated on the electronics [3] and be located
above the refrigerant lines [1].
▶ Evenly tighten the screw hooks until the thickness of the foam
between the casing and the air outlet on the cover is roughly
4-6 mm. The edge of the cover should be tight against the ceiling.
▶ Remove the foam parts from the inside of the unit.
Only reinstall the air inlet grille when establishing the electrical
connection.
Climate 5000 M – 6721849819 (2022/09)
4.3.4

Install the rack-mounted unit on the wall

▶ Open the box at the top and lift the indoor unit out and up.
▶ Place the indoor unit with the moulded parts of the packaging
face down.
▶ Undo screw and remove the mounting plate on the rear of the indoor
unit ( Figure 120. For routing the pipes through the indoor unit,
we recommend loosening the plate on the underside and reattaching
it later.
▶ Determine the installation location, taking the minimum clearances
into consideration ( Fig. 119).
▶ Attach the mounting plate with a screw and wall plug centrally and at
the top of the wall and level out ( Fig. 121).
▶ Fasten the mounting plate with a further four screws and wall plugs so
that the the mounting plate lies flat on the wall. We recommend using
the holes marked with arrows.
▶ Drill wall outlet for the piping (wall outlet should be behind the indoor
unit as a recommendation  Fig. 121).
▶ If a skirting board is present, adapt the panel to the skirting board on
the lower edge with the aid of tools ( Figure 122).
The pipe fittings on the indoor unit are generally located behind the
indoor unit. We recommend extending the pipes before mounting the
indoor unit.
▶ Establish pipe connections as described in chapter 4.6.
▶ Bend the piping in the required direction if necessary, and knock out
an opening on the side of the indoor unit.
▶ Route the piping through the wall and attach the indoor unit to the
mounting plate.
▶ If necessary, open the front cover and remove the filter element
( Figure 123) in order to insert the cold catalyst filter from the
scope of supply.
4.3.5

Install the wall-mounted indoor unit on the wall

▶ Open the box at the top and lift the indoor unit out and up.
▶ Place the indoor unit with the moulded parts of the packaging face
down ( Fig. 130).
▶ Undo screw and remove the mounting plate on the rear of the
indoor unit.
▶ Determine the installation location, taking the minimum clearances
into consideration ( Fig. 129).
▶ Attach the mounting plate with a screw and wall plug centrally and at
the top of the wall and level out ( Fig. 131).
▶ Fasten the mounting plate with a further four screws and wall plugs so
that the the mounting plate lies flat on the wall.
▶ Drill wall outlet for the piping (wall outlet should be behind the indoor
unit as a recommendation  Fig. 132).
▶ Change the position of the condensate pipe if necessary ( Fig. 133).
The pipe fittings on the indoor unit are generally located behind the
indoor unit. We recommend extending the pipes before mounting the
indoor unit.
▶ Establish pipe connections as described in chapter 4.6.
Installation
113