Hoonved C 43 E Série Mode D'emploi Et Entretien page 25

Part 2: For the operator
WASHING PHASES C/SP E
2.1
2.1.a Switching on and Preparing the machine
To switch on the machine, press the power switch (Q1)
into the ON position.
Will become CONSTANTLY LIT
LED and the tank temperature LED (LTV).
CHECK
C
IMPORTANT
On first switching on, LED
The boiler, and then the tank, will start to fill automatically.
Once the water level has been reached, the heating
elements will switch in, first in the boiler, then in the tank.
Once the water in the tank reaches the correct tempera-
ture, the tank temperature LED (LTV) will go ON.
WASHING OPERATION
If not equipped with an automatic dosing system, pour
into the tank a quantity of detergent suitable for the volu
me and hardness of the water. For quantities, refer to the
specific instructions for the detergent in use.
ATTENTION
When items to be washed are encrusted with burnt
on matter, or a long time has passed between use
and washing, it is essential to carry out a pre-was
soak using a suitable softening agent.
The use of hand-washing products is to be avoided
as they could produce foam inside the machine.
IPlace the basket of items to be washed inside the machine,
having first removed any solid waste.
2.1.b Selecting a Cycle
The duration of the washing cycle can be chosen from
three different lengths of time (SHORT, MEDIUM, LONG),
"CYCLE
to be selected using the
Each time the "CYCLE (S9)" button is pressed, the blue
LEDs LC1 or LC2 or LC1
LC2 CHECK
as will the
LC2 will light up.
(S9)" button.
and LC2 together.
2.1.c STARTING THE WASHING CYCLE
To start the washing cycle, press and hold the
(S3) button for a few seconds, then release.
Throughout the washing cycle the LED(s) for the selected
(LC1 LC2 or LC1
cycle or and
ATTENTION
We recommend that you top up the detergent used up
by washing grease or dispersed during rinsing every 4-5
complete cycles.
The use of the machine ensures rinsing at the ideal tem-
perature for hygienic purposes every time;
Indeed, if the temperature is not sufficient the wash will
be automatically prolonged so as to ensure the necessary
conditions of optimum rinsing at 85°C.
The waiting time required to attain optimum temperature
can extend to a maximum of 8 minutes.
While this is taking place, the
RAPIDLY until the end of the cycle. To reset the flashing,
switch the machine off and back on using the power
switch (Q1) .
2.1.d Interrupting the cycle
1) It is possible to interrupt the washing cycle momentarily
by opening the door, this is an EMERGENCY measure:
LC2 or LC1
the cycle LEDs (LC1 or
will start to FLASH, alternating with the
On closing the door, operations will resume from the point
in which they stopped.
2) The cycle can also be interrupted by SWITCHING the
machine's power switch (Q1) to the OFF position.
3) On switching the machine back on, the LED indicating
the last cycle selected will light up.
At the end of the washing cycle, take out the basket
and shake it gently so as to remove the last drops
left on the washed items.
Allow items to dry and remove them from the basket with
clean hands.
Store all items on hygienic and completely stable surfaces.
2.1.e Manual Draining
It is possible to drain the water from the tank at any time
during the day, according to the waste accumulated.
To carry out this operation, proceed as follows:
- Switch the machine's power switch (Q1) to the OFF
position and release the overflow, allowing all the water
to drain from the tank;
- Remove the tank filters (22/23) and clean;
ENGLISH
START
LC2 together)
will FLASH.
CHECK
LED will FLASH
LC2 together)
and
CHECK
LED.
25