Concept VP8370 Mode D'emploi page 19

Table des Matières

CHECKING THE DUST COLLECTION BAG FILL

When the dust collection bag ll indicator turns red during operation, replace the full dust collection bag immediately.

If the dust collection bag ll indicator is still red after the bag has been replaced, this may be due to several causes:

- some of the air passages (hoses, telescopic tube, suction inlet, brush adapter, or other adapters) are obstructed;

- the motor lter is dirty;

- the air outlet lter is dirty.

Check for each of the possible causes above and eliminate the problem before you start vacuuming. If the cause of the

problem cannot be identi ed, hand over the product to the nearest service centre. Never use the vacuum cleaner if the

bag level indicator is completely red during operation. The motor could be damaged irreparably

CLEANING AND MAINTENANCE

You may clean the accessories and the appliance with a wet cloth. Never immerse

the appliance in water! Do not use any aggressive substances for cleaning, such as

solvents or abrasives!

REPLACING THE DUST COLLECTION BAG

1. Unplug the product from the mains. Disconnect the hose from the suction inlet

and open the appliance cover.

2. Push the ap on the dust retention bag holder; remove the used dust retention

bag (Fig. 3). Dispose of a paper or SMS dust collection bag. Be careful not to tear

the bag when handling.

the bag when handling. If the bag is made of fabric, empty it and close it

carefully - it can be used repeatedly.

3. Insert a new or empty dust retention bag by tting the plate in the bag holder. The

bag opening must be aligned with the hose hole in the appliance cover.

4. Never use the vacuum cleaner without the dust bag installed! If you forget to

insert the dust retention bag or you insert it incorrectly, the appliance's motor

may become damaged.

5. Close the cover. Press until you hear a click.

REPLACING FILTERS

• The lters should be cleaned or replaced when they are visibly dirty, or if the

appliance's suction power is reduced. Always check the lters after using the

appliance.

• In order to avoid damage to the appliance, do not use it with incorrectly installed

lters.

• Before replacing the lters, disconnect the appliance from the electrical socket.

• You can buy suitable types of lters from your dealer, or you can order them from

the manufacturer.

CLEANING AND REPLACEMENT OF THE MOTOR FILTER

1. Disconnect the exible hose and open the appliance cover.

2. Pull the dust collection bag out of its holder so that you can access the motor lter

more easily.

3. Remove the motor lter (Fig. 4). You can clean the lter by tapping it. If the lter is

heavily soiled, you may wash it in lukewarm water and let it dry properly.

4. Insert the cleaned or new motor lter into the appliance and close the cover.

CLEANING AND REPLACING THE AIR OUTLET FILTER

1. Open the air outlet grid in the appliance's rear section (Fig. 5).

2. Remove the air outlet lter. You can clean this lter by tapping it, then brushing it

2. Remove the air outlet lter. This type of vacuum cleaner is equipped with a

with a soft brush. After this operation is complete, you may clean a very dirty lter by

H.E.P.A. lter in the outlet, which is capable of catching even very ne dust

washing and brushing with a soft brush in lukewarm water with no cleaning agents

particles. You can clean this lter by tapping it, then brushing it with a soft

added. It is important to let the wet parts dry thoroughly. A wet lter will be dam-

brush. After this operation is complete, you may clean a very dirty lter by

aged by vacuuming! Do not use a hair dryer to dry it!

washing and brushing with a soft brush in lukewarm water with no cleaning

Note: Wet cleaning may cause more wear and tear of the lter and, consequently,

agents added. It is important to let the wet parts dry thoroughly. A wet lter

may shorten its service life.

will be damaged by vacuuming! Do not use a hair dryer to dry it!

3. Insert the cleaned or new air outlet lter into the appliance and close the air outlet

Note: Wet cleaning may cause more wear and tear of the lter and,

grid.

consequently, may shorten its service life.

3. Insert the cleaned or new air outlet lter into the appliance and close the air

outlet grid.

TROUBLESHOOTING

Motor does not run.

Motor has stopped

operating.

Front cover cannot be

(Fig. 3)

closed

Reduced suction power

Vacuum cleaner heats

The following appliance accessories can be purchased additionally:

SMS dust bags (5 units + 2 units of motor lters) Order code sms9000

Fabric dust bag, 1

Motor lter

(Fig. 4)

H.E.P.A. air outlet lter

VP8370

Wet cleaning may cause more wear and tear of the lter and,

Problem

Cause

Plug inserted into the mains outlet

incorrectly or insu ciently.

The mains outlet is not live.

Improper or insu cient air ow. Motor

overheating fuse activated.

Dust bag inserted incorrectly.

Dust bag full or clogged.

Obstructed lter.

Clogged nozzle, tube, or hose.

Slight heating of the vacuum cleaner is normal and cannot be considered a failure.

Ord. No. ts9180

Order code44290910

Order code 44290911 Priced according to the valid price list

(Fig. 5)

Solution

Check the plug connection.

Check for voltage, e.g. by connecting

another appliance.

Disconnect the cable from the socket.

Check and release the air suction

and discharge holes; check the lter's

cleanliness and/or replace the dust bag.

Let the vacuum cleaner cool down.

Check the dust lter installation.

Replace the dust bag.

Clean or replace the lter.

Check and clear the air passage on the

suction and discharge sides.

Priced according to the valid price list

Price according to the applicable price list

Price according to the valid price list

Table des Matières

Concept VP8370 Mode D'emploi page 19

Manuels Connexes pour Concept VP8370

Produits Connexes pour Concept VP8370

Table des Matières