Safety Instructions; Tool Specifications - Haussmann BN1850 Guide De L'utilisateur

SAFETY INSTRUCTIONS

EYE PROTECTION which conforms to ANSI specifications and provides protection
against flying particles both from the FRONT and SIDE should ALWAYS be worn by
the operator and others in the work area when loading, operating or servicing this
tool. Eye protection is required to guard against flying fasteners and debris, which
could cause severe eye injury.
The employer and/or user must ensure that proper eye protection is worn. Eye
protection equipment must conform to the requirements of the American National
Standards Institute, ANSI Z87.1 and provide both frontal and side protection.
NOTE: Non-side shielded spectacles and face shields alone do not provide
adequate protection.
CAUTION: ADDITIONAL SAFETY PROTECTION will be required in some
environments. For example, the working area may include exposure to noise level
which can lead to hearing damage. The employer and user must ensure that any
necessary hearing protection is provided and used by the operator and others in the
work area. Some environments will require the use of head protection equipment.
When required, the employer and user must ensure that head protection conforming
to ANSI Z89.1 is used.
AIR SUPPLY AND CONNECTIONS
Do not use oxygen, combustible gases, or bottled gases as a power source for this
tool as tool may explode, possibly causing injury.
Do not use supply sources which can potentially exceed 200 P.S.I.G. as tool may
burst, possibly causing injury.
The connector on the tool must not hold pressure when air supply is
disconnected. If a wrong fitting is used, the tool can remain charged with air after
disconnecting and thus will be able to drive a fastener even after the air line is
disconnected, possibly causing injury.
Do not pull trigger or depress contact arm while connected to the air supply as the
tool may cycle, possibly causing injury.
Always disconnect air supply: 1.) Before making adjustments; 2.) When servicing the
tool; 3.) When clearing a jam; 4.) When tool is not in use; 5.) When moving to a
different work area, as accidental actuation may occur, possibly causing injury.
LOADING TOOL
When loading tool: 1.) Never place a hand or any part of body in fastener
discharge area of tool; 2.) Never point tool at anyone; 3.) Do not pull the trigger or
depress the trip as accidental actuation may occur, possibly causing injury.
OPERATION
Always handle the tool with care: 1.) Never engage in horseplay; 2.) Never pull
the trigger unless nose is directed toward the work; 3.) Keep others a safe
distance from the tool while tool is in operation as accidental actuation may occur,
possibly causing injury.
The operator must not hold the trigger pulled on contact arm tools except
during fastening operation as serious injury could result if the trip accidentally
contacted someone or something, causing the tool to cycle.
Keep hands and body away from the discharge area of the tool. A contact arm tool
may bounce from the recoil of driving a fastener and an unwanted second fastener
may be driven possibly causing injury.
Check operation of the contact arm mechanism frequently. Do not use the tool if
the arm is not working correctly as accidental driving of a fastener may result. Do
not interfere with the proper operation of the contact arm mechanism.
Do not drive fasteners on top of other fasteners or with the tool at an overly steep
angle as this may cause deflection of fasteners which could cause injury.
Do not drive fasteners close to the edge of the work piece as the wood may split,
allowing the fastener to be deflected possibly causing injury.
MAINTAINING THE TOOL
When working on air tools note the warnings in this manual and use extra care
-12-

TOOL SPECIFICATIONS

All screws and nuts are metric.
MODEL TOOL ACTUATION
1850BN Sequential Trip
FASTENER SPECIFICATIONS:
TOOL MODEL BRAD SERIES GAUGE
1850BN BT1300 18
TOOL AIR FITTING:
This tool uses a free-flow connector plug, 1/4 N.P.T. The inside diameter should be
.200" (5mm) or larger. The fitting must be capable of discharging tool air pressure when
disconnected from the air supply.
OPERATING PRESSURE:
70 to 100 PSI. Select the operating pressure within this range for
best fastener performance.
DO NOT EXCEED THIS RECOMMENDED OPERATING PRESSURE.
OPERATION
SEQUENTIAL TRIP
The Sequential Trip requires the operator to hold the tool against the work before pulling
the trigger. This makes accurate fastener placement easier, for instance on framing, toe
nailing and crating applications.
The Sequential Trip allows exact fastener location without the possibility of driving a
second fastener on recoil, as described under "Contact Trip".
The Sequential Trip Tool has a positive safety advantage because it will not accidentally
drive a fastener if the tool is contacted against the work – or anything else – while the
operator is holding the trigger pulled.
MODEL IDENTIFICATION:
SEQUENTIAL TRIP
GRAY TRIGGER
Identified by:
LENGTH HEIGHT WIDTH
9" (235 mm) 9.86" (241 mm) 2" (50 mm) 2.56 lb (1,2 kg)
FASTENER RANGE
5/8" - 2" (16 mm – 50 mm)
-13-
WEIGHT