REBER Professional 30 Eco Notice D'utilisation Et Entretien page 10

Table des Matières

Publicité

Les langues disponibles

Les langues disponibles

3
INSTALLATION
The surface where the machine has to be installed must take into consideration the support dimensions. Furthermore, it must be smooth, dry, strong
and with an height from the ground of about 80 cm. and with around the necessary space for use and maintenance.
Environmental conditions :
Minimum temperature +10° - Max. temperature + 38°
Minimum moisture 30% - Max. moisture 80%
ELECTRICAL CONNECTION
Preliminary controls
Before connecting the machine to a socie, take care:
-
Make sure the socket is provided with a ground protection
-
Make sure that the voltage and frequency of supply correspond to those indicated on the data plate of the machine
-
Make sure about the way on how to connect the power cable to avoid the possibility of sliding and tripping
-
It is user responsibility that the connection of the machine to the electric system is in compliance with the rules in force in the country
where the machine is installed, and it has been make by a qualified technician.
-
Once all preliminary controls have been correctly done, use the main power switch to start use you machine
USE OF THE MACHINE
This machine is provided by an innovative technology suitable to reach high performances with energy saving ( just to 50% less compares to the
normal machines in commerce with same performances).
The seal power is checked by the electronic card that gives to the sealing bar always the correct power independently from the network voltage.
The seal control is a mix from an electronic base and mechanical control.
Once connected, the machine is ready for use by the switch (1).
The machine permits the vacuum packaging conservation of food products, so as to extend their conservation in time
Default setting:
1-
Minimum electronic power of sealing of 2 units time/power , suitable for 95/105 microns bags fournished ( Potentiometer on lower level)
; starting work, with cold machine place the knob on second level and progressive lower the power
2-
Turning the pontentiometer's knob (9) the electronic time settled can be multiplied per 10 ;
3-
It is possible to modify the electronic base of seal power by programming the electronic card.
4-
Cod. 9709 NE default power is 5 units, it is possible to change this power by electronic setting
5-
The machine is settled in automatic cycle vacuum/seal,
6-
It is possible to pass on manual cycle by programming the electronic card.
7-
The machine is settled by a waiting time of 10 sec. from the reaching of the vacuum level and the starting of the seal cycle to obtain more
vacuum; it is possible to change this time by programming the electronic card.
8-
The machine is settled by a waiting time at the end of the seal cycle to obtain a best quality seal; this waiting time can be stopped by press
the Start cycle switch (1) when the Led (12) switch off indicated the seal cycle is finished
ELECTRONIC SETTINGS
SETTING THE MACHINE TO MANUAL/AUTOMATIC USE
To set the machine to manual use, proceed as described below:
Before connecting the plug to power supply, press and hold on Start cycle switch ( 1 );
Connect the plug to power supply;
Wait for at least 5 seconds;
Release the switch.
To set the machine to automatic use, proceed as described below:
Before connecting the plug to power supply, press and hold on Seal switch ( 2 );
Connect the plug to power supply;
Wait for at least 5 seconds;
Release the switch.
(The setting will last when unplugging the machine, until a new programming operation will be made).
WELDING POWER SETTING
If some problems of pre-welding arrives it is possible to reduce start seal power of 50%
Proceed as described below to change welding base time (these operations are to be made while the machine is plugged in):
press and hold on Seal switch ( 2 );
press and hold on Start cycle switch ( 1 );
wait at least for 2 seconds to enter programming mode;
release and press Seal switch (2) 1 time
release both switches (This setting will last when unplugging the machine, until a new programming operation will be made).
INFO:
Sealing time could be different using different kind of bags even if thickness is the same; we suggest to test welding after changing welding time.
IMPORTANT
If the machine is not used for a long period and/or in the case of non-adequate or low temperatures, it is recommendable, before using the machine, to
try it once without using the bag and keep the machine working in vacuum conditions for some seconds.

Publicité

Table des Matières
loading

Ce manuel est également adapté pour:

Professional 30Professional 30 filter9709 ne9709 n9709 nf

Table des Matières