Publicité
-
Carefully follow instructions provided during maintenance operations.
-
For maintenance and storage of protective glasses, see the instructions for use provided with them.
-
To replace oxygen and gas cylinders it is recommended to:
a.
Ensure that the cartridge is empty before replacing it;
b.
For oxygen
on items
555C – 555CA12 – 555D – 555DA12 - 555K – 555KA12 - 555H400 – 555H400K:
completely the regulator by turning the adjusting screw anticlockwise;
on item 555KM - 555KMA12 (with manometers): close completely the regulator by turning the
adjusting screw clockwise;
c.
For gas
(on all the models):
d.
Unscrew the empty cylinder;
e.
Screw the new cylinder and repeat steps from point (3) of the instructions for use;
-
To replace the tip of the torch, unscrew the mounted tip and screw in the desired one.
Important note: NEVER use grease or oil on parts that come into contact with oxygen
Consider the following cases of malfunctioning:
1.
The flame suddenly extinguishes and you can hear a loud blast due to a sudden obstruction of bit nozzle, this
blast is generated by the ignition of gas blend within the bit. The easiest solution is to allow the corpuscle
to come out from the nozzle by rubbing the bit on an appropriate tablet. If this is not successful, you should
allow the torch to cool down, then remove the bit and clean its inner part with proper material that does not
scratch its brass surface. Scratches can alter the nozzle material characteristics.
2.
You hear several consecutive blasts, this is due to bit overheating after a long use of the equipment. High
temperature causes the gas blend to pre-ignite within torch. You should stop your work until bit has
completely cooled down. If you cannot interrupt your work, close the acetylene stopcock to allow oxygen
flow and quick torch cooling.
3.
In case of a leaks, check that all stopcocks are closed; check that all components are properly connected and
repeat all start-up operations. If leakage persists, disconnect gas and oxygen cylinders and replace them with
appropriate replacement parts.
4.
If flame is unsteady or detached, adjust gas supply by closing the oxygen stopcock and repeating all steps
from point (3).
Important note: if filler metals are used, joint has to be deoxidized with specific materials.
SAFETY
Welding equipment regulators ensure supply at a low and constant pressure. In addition, the equipment has two
non-return valves that ensure equipment safety.
WHAT TO DO IN THE EVENT OF A FIRE
Immediately close oxygen cylinder, this should be enough to extinguish the flame.
Close gas cylinder as well and extinguish fire with appropriate fire-fighting equipment.
ВНИМАТЕЛЬНО ПРОЧИТАЙТЕ ДАННУЮ ИНСТРУКЦИЮ ПЕРЕД ТЕМ, КАК НАЧНЕТЕ ПОЛЬЗОВАТЬСЯ
ИНСТРУМЕНТОМ. ПЕРЕЧИТЫВАЙТЕ ЕЕ, ЕСЛИ ЭТО НЕОБХОДИМО.
Не повреждайте оборудование. Изменение, удаление компонентов и / или использование частей, не
рекомендованных производителем, может быть очень опасно.
Убедитесь в том, что оборудование используется только квалифицированными специалистами, а также
соблюдаются все законы безопасности труда.
Данное оборудование поставляется с одноразовыми кислородными баллонами (белый, арт. 571 или
571A12) и газовым баллоном NOVACET (красный, арт. 580), газовым баллоном SUPERGAS (оранжевый, арт.
575), а также газ. бал. KEMAP 58, все заправлены и готовы для работы.
Строго рекомендуется использовать только оригинальные сменные части KEMPER, арт. 571 или 571A12
(кислородный баллон), арт. 580 (баллон NOVACET), арт. 575 (баллон SUPERGAS), арт. 581 (баллон KEMAP),
а также оригинальные запчасти. Использование различных видов газовых баллонов может быть опасно.
close completely the regulator by turning the orange screw clockwise;
RU
РУКОВОДСТВО ПО ЭКСПЛУАТАЦИИ
- 11 -
RU
close
Publicité
