Télécharger Imprimer la page

Simons Voss Technologies Digital SmartHandle AX Reader on both sides Guide Abrégé page 31

Publicité

Digital SmartHandle AX Reader on both sides
Loss of the precise guidance of the handle
It may be difficult to install on mortise locks with a retaining nut.
Do not mechanically alter the locking nut. The handle would then lose
its precise guidance.
Difficult installation due to inaccurate holes
The fitting cannot be installed if the fastening holes and the spindle do not
match.
Make sure that the fastening holes and the spindle are in parallel ver-
tical lines.
NOTE
Active and hybrid technology only with shortened range
The active and hybrid technologies have a significantly greater range. Under
normal operating conditions, both SmartHandle AX are reached at the same
time and communication errors may occur.
Activate the checkbox for a shortened range for both sides on the
SmartHandle AX in LSM/AXM.
Effect on the mortise lock
The SmartHandle AX acts exclusively on the latch of the mortise lock.
Locking and insurances
Insurance companies place increased demands on a closure.
1.
If you want to lock the door under insurance law, use a self-locking
panic lock or a locking cylinder in addition to the SmartHandle AX.
2.
Pay attention to the approvals according to EN 179.
SmartHandle AX with self-locking panic lock
The SmartHandle AX only offers full functionality with a self-locking panic
lock.
1.
Combine the SmartHandle AX with a self-locking panic lock.
2.
Pay attention to the declarations of conformity of the lock manufactur-
ers according to EN 179.
Conditions for authorisation security
Operation with Mifare Classic and/or PinCode keypad excludes authorisation
security class D according to DIN EN 16867:2020.
Sealing escutcheon holes
Any escutcheon holes that exist may be used to manipulate the lock.
1.
Seal any escutcheon holes with a blind cylinder, for example.
2.
In the case of FH versions, you must be install a brass dummy cylinder or
locking cylinder.
Rest time for anti-slip surface
The supplied adapter plate feature a non-slip surface. This requires a settling
time for it to be fully effective.
1.
After installing the adapter plate, wait five hours before continuing with
the installation.
2.
If you need to finish installing beforehand, do not turn the handle as far
as it will go.
4. Scope of delivery
SmartHandle AX (For installation on both sides, consisting of adapter
plates and inner part. The stationary SmartHandle AX for the outer part
is not included.)
Special tool
Quick guide
Depending on version:
Adapter set, 7 mm spindle
Adapter sleeve, 8.5 mm spindle
Adapter sleeve, 9 mm spindle
Adapter sleeve, 10 mm spindle
EN
5. Design
1
6. Prepare door (drilling template)
Pin or scriber at hand.
ü
Drill at hand.
ü
Suitable drill bit at hand (depending on mortise lock hole diameter:
ü
8.5 mm/9.5 mm/10.5 mm).
PH2 screwdriver at hand.
ü
1.
Insert the spindle into the mortise lock.
2
2.
Place the drilling template on the spindle.
3
3.
Align the drill template vertically using the printed scale.
4.
Mark the points to be drilled on the door.
4
5.
Remove the drilling template.
5
6.
Remove the spindle.
6
7.
Remove the mortise lock (PH2).
7
8.
Measure the diameter of the fastening holes.
8
Ø fastening holes
5.5 mm–6.3 mm
6.4 mm–7.3 mm
7.4 mm–8.7 mm
≥ 8.8 mm
9.
Determine the required drill bit based on the measured diameter.
10. Drill the required holes.
9
11.
Fit the mortise lock (PH2).
10
7. For door thickness X: prepare threaded
rods and spindle
Saw at hand.
ü
Vernier calliper at hand.
ü
ü
PH2 screwdriver at hand.
1.
For X: measure the door thickness.
11
2.
For X: fasten the screws, threaded sleeves and threaded rods together.
12
3.
For X: mark the sawing points on the threaded rods and spindle.
13
14
4.
For X: use a suitable saw to cut the threaded rods and spindle.
15
8. Programming the fitting
Programme the fitting before installation. You can use different
programming devices, depending on the product family.
4. Scope of delivery
Drill bits required
8.5 mm
8.5 mm
9.5 mm
10.5 mm
31 / 60

Publicité

loading