Télécharger Imprimer la page

DeWalt DCMWP234 Traduction De La Notice D'instructions Originale page 21

Publicité

Les langues disponibles

Les langues disponibles

Cutting Load Meter Indicator (Fig. U)
The cutting load meter indicator
yellow or red when mowing.
White indicates a low cutting load.
Yellow indicates a medium cutting load.
Red indicates a high cutting load. Runtime will be
reduced if there is a prolonged high load while mowing.
Overheat Indicator (Fig. U)
The overheat indicator
then blink when the batteries or motor is overloaded
during operation.
The overheat indicator
blink when the module has reached a high temperature.
To clear the overheat indicator
and mower to cool down. When cooled, restart the mower
and resume cutting with the mower deck set higher.
Blade Sharpening Indicator (Fig. U)
The blade sharpening indicator
the blades need service. Sharpen or replace the blades, refer
to the Blade Sharpening section in this manual.
Blade Reset Button (Fig. U)
nOTE: Ensure the battery packs 
are installed before attempting to reset.
To clear the blade sharpening indicator
on the control panel
12
bail handle 
 8 
to the main handle 
the blade reset button 
17
indicator 
 16 
 turns off.
Starting Mower (Fig. Q—T)

DANGER: Sharp moving blade. Never attempt
to override the operation of the switch box and
safety key system as serious injury could result.

WARNING: Ensure self drive is disengaged before
starting the mower
nOTE: Mower is operational when the battery packs 
safety key 
6
are installed.
1. Lift and hold the battery port cover 
battery port 
 38 
.
14
will illuminate white,
13
will illuminate amber and
13
will illuminate red and then
13
, allow the batteries
16
will illuminate when
 26 
and safety key 
16
, power
by pulling and holding the
 4 
. Press and hold
until the blade sharpening
up to expose the
 19 
2. Slide a battery pack 
audible click is heard. Repeat this process for the second
battery pack 
nOTE: Ensure both battery packs are fully seated and
fully latched into position before starting mower.
3. Close the battery port cover  
cover 
 19 
4. Insert safety key 
the main handle
key slot 
5. To power on the control panel
handle 
6. To start the mower blades, continue to hold the bail
handle 
power button 
nOTE: Once the mower starts you can release the
power button 
bail handle 
to stay running.
7. To turn the mower OFF, release the bail handle 

WARNING: Never attempt to lock a switch or bail
handle in the ON position.
nOTE: Once the bail handle 
position it will activate the "Automatic Braking Mechanism".
The motor is braked and the mower blades will stop rotating
in three seconds or less. If mower blades rotate longer than
three seconds, discontinue using mower and have it serviced.
DCMWSP256 ONLY
Self Drive System (Fig. V)

DANGER: Sharp moving blade. Never attempt to
override the operation of the switch box, the self
drive system or the safety key system as serious
injury could result.
Your mower DCMWSP256 is equipped with a self drive system
which functions independently of the mower blades.
1. To use self drive, press the self drive lever
main handle 
6
2. To turn off self drive, release the self drive lever
nOTE: During cutting, at times it may be easier to
maneuver around an object, such as a tree or plants, with
the self drive off. The mower can easily be used with the
self drive system off.
DCMWSP256 ONLY
Speed Adjustment Dial (Fig. W)
Your DCMWSP256 mower is equipped with a speed
adjustment dial 
The numbers on the speed adjustment dial 
quickly or slowly the self drive system propels the mower.
Choosing a lower number propels the mower at a slower
pace. Choosing a higher number propels the mower at a
 26 
and
faster pace.
1. To increase the speed of the self drive system, rotate the
speed adjustment dial 
nOTE: The speed adjustment dial 
higher number.
 26 
into the battery port
 26 
.
 19 
is fully closed before starting the mower.
6
into the key slot 
4
, until it is fully seated inside of the
 39 
as shown in Fig. T.
12
 8 
to the main handle 
 4 
 8 
to the main handle 
 4 
 11 
.
 11 
, but you must continue to hold the
 8 
to the main handle 
 8 
has returned to the original
 4 
.
 10 
located next to the LED dashboard
 10 
towards the rabbit icon
English
38
until an
. Ensure the battery port
 39 
, located on
, pull and hold the bail
.
and then press the
 4 
for the mower
 8 
.
9
towards the
9
.
12
.
 10 
indicate how
40
.
 10 
will display a
19

Publicité

loading

Ce manuel est également adapté pour:

Dcmwsp256