Publicité
Les langues disponibles
Les langues disponibles
English
battery pack in a warm environment such as in a metal
shed or an uninsulated trailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. If charging problems persist, take the tool, battery
pack and charger to your local service center.
4. You may charge a partially used pack whenever you
desire with no adverse effect on the battery pack.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
a cloth or soft non‑metallic brush. Do not use water or
any cleaning solutions.
Wall Mounting
Some DEWALT chargers are designed to be wall mountable
or to sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet, and
away from a corner or other obstructions which may impede
air flow. Use the back of the charger as a template for the
location of the mounting screws on the wall. Mount the
charger securely using drywall screws (purchased separately)
at least 1" (25.4 mm) long, with a screw head diameter of
0.28–0.35" (7–9 mm), screwed into wood to an optimal
depth leaving approximately 7/32" (5.5 mm) of the screw
exposed. Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
ASSEMBLY AND ADJUSTMENTS
DANGER: To reduce the risk of serious personal
injury, turn unit off and remove the safety key and
battery packs before making any adjustments or
removing/installing attachments or accessories.
An accidental start‑up can cause injury.
Single Touch Handle Adjustments
(Fig. D, E)
The mower is shipped in the storage position. You will need
to adjust the single touch handle
before continuing.
Raise the Single Touch Handle (Fig. D)
1. To unlock the single touch handle
position, squeeze the handle unlock button
nOTE: The handle unlock button
back of handle support
nOTE: The main handle
both sides of the single touch handle tubes before lifting
the single touch handle
shown in Fig. D,.
16
1
to the operating position
1
from the storage
3
.
is located on the
3
2
.
must pop out slightly from
4
1
from the storage position as
2. Raise the single touch handle
Listen for an audible click and ensure the single touch
handle
1
is locked into position before proceeding.
3. Extend the main handle
clicks is heard. The single touch handle
operation position.
nOTE: Take care to not pinch, pull or otherwise stress
the cord
28
.
Adjusting the Main Handle Height
(Fig. F)
The main handle
4
extends to accommodate taller users.
1. To extend the main handle
position, press the handle release button
main handle away from the handle support
audible click is heard, indicating that it is locked into the
lower height position.
nOTE: The handle release button
bottom of handle support
2. To extend the main handle
position, press the handle release button
main handle away from the handle support
audible click is heard, indicating that it is locked into the
upper height position.
3. Ensure the main handle
before proceeding.
nOTE: When the batteries
inserted and the bail handle
folding indicator
15
handle
1
is not locked into position.
4. To retract the main handle
postion, press the handle release button
main handle
4
towards the handle support
audible click is heard, indicating that it is locked into
the lower height position.
Storage Mode (Fig. G—L)
DANGER: MAKE CERTAIN THE SAFETY KEY IS
REMOVED TO PREVENT ACTUATION BEFORE
REMOVING OR INSTALLING BATTERIES.
DANGER: Turn unit off and remove safety key and
battery packs.
1. To retract the main handle
button
5
and push the main handle
handle support
2
until two audible clicks are heard,
indicating that both sides of the handles are locked
into position. The main handle
against the handle support.
nOTE: The main handle
windows
29
. If they are not engaged as shown in Fig. G,
press the main handle
until two audible clicks are heard and both sides of
handle windows
29
nOTE: Ensure the two storage latches
the single touch handle
in Fig. J before lowering the single touch handle
the stoarge position.
2. Fold the single touch handle
wheels
32
into storage position. Listen for two audible
1
to the locked position.
4
outward until a set of audible
1
is now in the
4
to the lower height
5
and pull the
2
5
is located on the
2
.
4
to the upper height
5
and pull the
2
4
locks into position
26
and safety key
8
is pulled, the handle
will illuminate if the single touch
4
to the lower height
5
and push the
2
4
, press the handle release
4
towards the
4
must be fully seated
4
must fully engage the handle
4
towards the handle support
are closed as shown in Fig. H.
30
at the back of
1
tubes pop outward as shown
1
towards the front
until an
until an
6
are
until an
2
1
into
Publicité
