Bosch EasySander 12 Notice Originale page 13

Technical data
Cordless multi-sander
Article number
Rated voltage
No-load speed
No-load orbital stroke rate
Sanding sheet surface
Orbit diameter
Weight according to
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging
A)
– during operation and
during storage
Recommended batteries
Recommended chargers
A) Limited performance at temperatures <0 °C
Noise/Vibration Information
Noise emission values determined according to
EN 62841-2-4.
Typically, the A-weighted sound pressure level of the power
tool is less than 70 dB(A). Uncertainty K=3 dB. The noise
level when working can exceed 80 dB(A).
Wear hearing protection
Vibration total values a (triax vector sum) and uncertainty K
h
determined according to EN 62841-2-4:
2 2
a =5.5 m/s , K=1.5 m/s .
h
The vibration level and noise emission value given in these
instructions have been measured in accordance with a
standardised measuring procedure and may be used to com-
pare power tools. They may also be used for a preliminary
estimation of vibration and noise emissions.
The stated vibration level and noise emission value repres-
ent the main applications of the power tool. However, if the
power tool is used for other applications, with different ap-
plication tools or is poorly maintained, the vibration level
and noise emission value may differ. This may significantly
increase the vibration and noise emissions over the total
working period.
To estimate vibration and noise emissions accurately, the
times when the tool is switched off or when it is running but
not actually being used should also be taken into account.
This may significantly reduce vibration and noise emissions
over the total working period.
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping their hands warm,
and organising workflows correctly.
Bosch Power Tools
Assembly
EasySander 12
u
3 603 J76 9..
V= 12
−1
min 11000
−1
min 22000
Charge the battery
2
cm 104
u
mm 1.2
kg 0.70
Note: The battery is supplied partially charged. To ensure
full battery capacity, fully charge the battery in the charger
before using your power tool for the first time.
°C 0 to +45
The lithium-ion battery can be charged at any time without
°C –20 to +50
reducing its service life. Interrupting the charging process
does not damage the battery.
PBA 10,8V...
The lithium-ion battery is protected against deep discharge
PBA 12V...
by the "Electronic Cell Protection (ECP)". When the battery
AL 11.. CV
is discharged, the power tool is switched off by means of a
GAL 12..
protective circuit: The application tool no longer rotates.
u
Note: If the power tool shuts down automatically because
the battery is flat or overheated, switch the power tool off
using the on/off switch (2). Charge the battery or let it cool
down before switching the power tool on again. Failure to do
so can damage the battery.
To remove the battery (3), press the release button (4) and
pull the battery back and out of the power tool. Do not use
force to do this.
Follow the instructions on correct disposal.
Dust/chip extraction
The dust from materials such as lead paint, some types of
wood, minerals and metal can be harmful to human health.
Touching or breathing in this dust can trigger allergic reac-
tions and/or cause respiratory illnesses in the user or in
people in the near vicinity.
Certain dusts, such as oak or beech dust, are classified as
carcinogenic, especially in conjunction with wood treatment
additives (chromate, wood preservative). Materials contain-
ing asbestos may only be machined by specialists.
– Use a dust extraction system that is suitable for the ma-
– Provide good ventilation at the workplace.
– It is advisable to wear a P2 filter class breathing mask.
The regulations on the material being machined that apply in
the country of use must be observed.
u
External dust extraction (see figures B–C)
When working without dust extraction, close the extraction
outlet (8) with the dust protection cover (9).
Remove the battery from the power tool before carry-
ing out work on the power tool (e.g. maintenance,
changing tool, etc.). The battery should also be re-
moved for transport and storage. There is risk of injury
from unintentionally pressing the on/off switch.
Use only the chargers listed on the accessories page.
Only these chargers are matched to the lithium-ion bat-
tery of your power tool.
Do not continue to press the On/Off switch after the
power tool has automatically switched off. The battery
can be damaged.
terial wherever possible.
Avoid dust accumulation at the workplace. Dust can
easily ignite.
1 609 92A 4N7 | (04.12.2018)
English | 13