Bosch GMB 32 Professional Notice Originale page 10

OBJ_BUCH-1761-003.book Page 10 Wednesday, September 14, 2016 2:46 PM
10 | English
5 Screw for drill fixture
6 Motor On/Off switch
7 Socket outlet for drill
8 Magnet On/Off switch
9 Insulated gripping surfaces
10 Safety chain
11 Lock nut
12 Set screw for adjustment of the guide rail
13 Open-end spanner
14 Hex key
A complete overview of accessories can be found in our accesso-
ries program.
Technical Data
Magnetic drill stand
Article number
Rated power input
Holding force of the magnet
Max. drilling dia.
(GBM 32-4, MK3 tool holder)
– Twist drill bit
– Core bit
Drill stroke, max.
Diameter of drill fixture
Weight according to
EPTA-Procedure 01:2014
Protection class
Declaration of Conformity
We declare under our sole responsibility that the product de-
scribed under "Technical Data" is in conformity with all rele-
vant provisions of the directives 2011/65/EU, 2014/30/EU,
2006/42/EC including their amendments and complies with
the following standards: EN 50581.
Technical file (2006/42/EC) at:
Robert Bosch Power Tools GmbH, PT/ETM9,
70538 Stuttgart, GERMANY
Henk Becker Helmut Heinzelmann
Executive Vice President Head of Product Certification
Engineering PT/ETM9
Robert Bosch Power Tools GmbH
70538 Stuttgart, GERMANY
Stuttgart, 01.01.2017
Assembly
Inserting the Drill
Remove the auxiliary handle from your drill, if required (see
the operating instructions of the drill).
Loosen screw 5 using an Hex key. Insert the drill with the drill
collar from above into the drill fixture 4 to the stop. Mount
1 609 92A 3A5 | (14.9.16)
screw 2 in order to connect the drill with the side holder 3.
Hand-tighten screw 5 using an Hex key.
 Check the tight seating of the drill in the drill fixture.
When the drill is not securely fastened, serious injury may
result.
Mounting the Safety Chain (see figure A)
For all work being performed in inclined, vertical or overhead
positions, secure the drill stand against falling down with the
provided safety chain 10.
 Before using the safety chain, check its proper func-
tion. Never use a damaged safety chain; replace a dam-
aged safety chain immediately.
Fasten the safety chain in such a manner that the drill stand
moves away from you, should it come undone.
Fasten the safety chain around the carrying handle of the drill
GMB 32
stand with as little play as possible.
0 601 193 0..
W 95
Operation
kN 25
 Pull the plug from the socket outlet and/or remove the
battery before carrying out adjustments on the power
tool or replacing accessory parts. Unintentional starting
mm 32
of drills is the cause of some accidents.
mm 12 – 60
 After each adjustment on the drill stand, retighten the
mm 223
bolts and locking handles.
mm 65
Starting Operation
 Observe correct mains voltage! The voltage of the pow-
kg 26,0
er source must agree with the voltage specified on the
/I
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
 Insert the mains plug of the drill only into socket outlet
7. Switch the drill on and lock the On/Off switch of the
drill with the lock-on button. Otherwise, the drill cannot
be switched on or off via the motor On/Off switch 6 on the
drill stand.
Push the magnet On/Off switch 8 upward and check if the drill
stand adheres to the workpiece surface.
To start the drill, press the motor On/Off switch 6 to position
"I".
Note: The drill can only be started when the magnet has al-
ready been switched on.
To switch off the drill, press the motor On/Off switch 6 to po-
sition "0".
Wait until the drill has come to a complete stop before push-
ing the magnet On/Off switch 8 downward in order to switch
the magnet off.
When not using the drill, switch it off in order to save energy.
Restarting Protection
The restarting protection prevents uncontrolled starting of
the drill after the power supply is interrupted.
For restarting the operation, press the motor On/Off switch
6 to position "I".
Note: Resumption of the power supply.
Bosch Power Tools