Accessories - Milwaukee M12 2315-20 Manuel De L'utilisateur

Using the PIVOTVIEW™ Cable
(Some Models or as an Accessory)
1. Install in the desired orientation according to "Con-
necting the Cable".
2. Carefully feed cable into desired area.
3. Turn the pivot knob to rotate the head up to 270º
on a single plane.
4. If the desired view is not achieved, press the
release buttons and rotate the pivot cable 90°.
Reattach to the socket. Bend or manipulate the
cable as needed.
Taking Images/Videos
Use the Image/Video
taking images or videos. The icon of the selected
mode is displayed in the upper left corner of the
display.
1. Adjust the cable to best fit the opening. After
checking the workspace for hazards, insert the
cable.
2. Use the ▲▼ buttons to zoom in or out on the
image.
3. Use the ◄► buttons to rotate the image in 90°
increments.
4. Use the LED brightness dial to increase/decrease
the light.
5. To take an image or begin a video, press the OK
button or pull the trigger.
6. To end the video, press OK or pull the trigger again.
7. To save the image/video, press OK or pull the
trigger. The image/video is saved onto the memory
card. Or, use the ◄► buttons to select Cancel.
8. NOTE: During a video recording, sound is also
recorded at the display if the MICROPHONE is
ON in Settings.
Press the Review
ages/videos.
1. Use the ◄► buttons to move through the stored
images/videos.
2. Press the OK button to select an image/video.
3. Use the ▲▼ buttons to select one of the following:
EDIT Zoom or rotate an image. Use the ▲▼
buttons to zoom. Use the ◄► buttons
to rotate in 90° increments.
PLAY Play back a video. Use OK to Pause/
Play. Use the ◄► buttons to Rewind/
Fast Forward.
DELETE Permanently delete an image/video.
FLAG Flag an image/video for future use. An
"F" is added to the front of the file name
for ease of locating when connected to
a computer.
DONE Return to Review screen
Reset Button
Use the reset button to restore to factory settings.
MAINTENANCE
To reduce the risk of injury, always
WARNING
unplug the charger and remove the
battery pack from the charger or tool before
performing any maintenance. Never disassemble
the tool, battery pack or charger. Contact a
MILWAUKEE service facility for ALL repairs.
Maintaining Tool
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
Inspect your tool for issues such as undue noise,
button to toggle between
Review
button to view the saved im-
misalignment or binding of moving parts, breakage of
parts, or any other condition that may affect the tool
operation. Return the tool, battery pack, and charger
to a MILWAUKEE service facility for repair. After six
months to one year, depending on use, return the
tool, battery pack and charger to a MILWAUKEE
service facility for inspection.
If the tool does not start or operate at full power with
a fully charged battery pack, clean the contacts on
the battery pack. If the tool still does not work prop-
erly, return the tool, charger and battery pack, to a
MILWAUKEE service facility for repairs.
To reduce the risk of personal in-
WARNING
jury and damage, never immerse
your tool, battery pack or charger in liquid or
allow a liquid to flow inside them.
Clean dust and debris from vents. Keep handles
clean, dry and free of oil or grease. Use only mild
soap and a damp cloth to clean, since certain clean-
ing agents and solvents are harmful to plastics and
other insulated parts. Some of these include gasoline,
turpentine, lacquer thinner, paint thinner, chlorinated
cleaning solvents, ammonia and household deter-
gents containing ammonia. Never use flammable or
combustible solvents around tools.
For repairs, return the tool, battery pack and charger
to the nearest service center.

ACCESSORIES

Use only recommended accesso-
WARNING
ries. Others may be hazardous.
For a complete listing of accessories, go online to
www.milwaukeetool.com or contact a distributor.
M-Spector FLEX™ 3' Inspection Camera Cable
Cat. No. 48-53-0150
M-Spector FLEX™ 9' Inspection Camera Cable
Cat. No. 48-53-0151
M-Spector FLEX™ 3' Inspection Camera Cable
with PIVOTVIEW™ Cat. No. 48-53-0155
SERVICE - UNITED STATES
1-800-SAWDUST
Monday-Friday, 7:00 AM - 6:30 PM CST
www.milwaukeetool.com
or visit
Contact Corporate After Sales Service Technical
Support with technical, service/repair, or warranty
questions.
Email: metproductsupport@milwaukeetool.com
B e c o m e a H e a v y D u t y C l u b M e m b e r a t
www.milwaukeetool.com to receive important
notifications regarding your tool purchases.
SERVICE - CANADA
Milwaukee Tool (Canada) Ltd
1.800.268.4015
Monday-Friday, 7:00 AM - 4:30 PM CST
or visit www.milwaukeetool.ca
LIMITED WARRANTY
USA & CANADA
Every MILWAUKEE power tool* (see exceptions below) is warranted
to the original purchaser only to be free from defects in material and
workmanship. Subject to certain exceptions, MILWAUKEE will repair
or replace any part on an electric power tool which, after examination,
is determined by MILWAUKEE to be defective in material or workman-
ship for a period of five (5) years** after the date of purchase unless
5
Cleaning
Repairs
(1.800.729.3878)