How To Use - Dyson AB06 Guide D'utilisation

Looking after your hand dryer

how to use

1. Insert your hands and the hand dryer will start automatically, creating sheets of air to scrape
water from your hands.
2. Move your hands up and down slowly through the air.
troubLeshooting guide
warning: risk of eLectric shock.
Problem
The hand dryer fails to start.
The hand dryer sometimes cuts out
when in use but resumes operation
after a period of time.
The dry time of the hand dryer has
increased.
The air flow from the hand dryer
has decreased.
If you have any further questions please contact the Dyson Helpline.
use in food PreParation areas
This hand dryer is certified by HACCP International for use in washrooms and food
preparation environments, if it is installed at least 2.5 metres from uncovered food.
If you are installing this hand dryer in a food handling or food manufacturing environment,
please contact the Dyson Helpline for the specialist installation guide that supports this.
cLeaning
The hand dryer should be cleaned daily. Follow these 3 simple steps to ensure the machine
performs to its best and remains hygienic. Using the wrong cleaning method or product may
invalidate your warranty.
1. Wipe with a mild sanitizing solution then rinse with water.
2. Clean the air inlets on the base REGULARLY.
3. Clean the floor beneath and around the unit. This may be required more regularly in high
use areas.
generaL advice
all cleaning chemicals should be used exactly as indicated by the manufacturer's
instructions (including appropriate dilution).
If a cleaning product is left on the machine for too long, a film will form. This may reduce the
effectiveness of the anti-microbial surfaces.
solution
Check fuse/circuit breaker is working and that the
power supply is connected. Must be performed by a
qualified electrician.
If a safe method of switching is available, turn the
unit on and off. If a safe method is not available, a
qualified electrician must perform this task.
Check the air inlet is clean and free of dust. If the air
inlet is dusty or dirty simply remove the dust or debris
with a soft cloth.
Inspect the inlet grille for dust and remove.
Inspect filters and change if required.
Inspect the inlet grille for dust and remove.
Inspect filters and change if required.
Any chemicals intended for use should first be tested on an inconspicuous area to confirm
suitability.
Aside from cleaning chemicals, care should be taken to avoid any harmful fluids from coming
into contact with the unit, in particular oils and alcohol-based products.
chemicaL guideLines
Many professional cleaning chemicals can be used. The following are some that are harmful to
the unit and should not be used. use of these will invalidate your warranty.
do not use:
Alcohol-acid mixes
Alcohol
Solvent /oil-based products
Quaternary ammonium
Alkali-bleach mixes
Foaming ingredients
Bleach or abrasive cleaners
do not pressure wash
water guideLines
This hand dryer has an IP35 certification.
Hand wash only. Do not pressure wash. Pressure washing may force water inside the casing
and thereby invalidate your warranty.
fiLter maintenance
Regularly check the air inlet at the base of the hand dryer to ensure that it is free from dust and
debris. Simply wiping the inlet with a soft cloth should be sufficient to remove dust and debris.
If required for high usage environments, a Dyson filter change kit provides everything needed
to change your unit's HEPA filter on site. Contact the Dyson Helpline on the number on the
back cover of this manual for more information.
Filter cleaning or replacement for your hand dryer can be carried out by carefully following
the instructions given in the filter change kit. If in any doubt, consult a qualified electrician or
contact the Dyson Helpline for support.
servicing
If your hand dryer needs servicing, please call the Dyson Helpline.
Also visit the website at www.dysonairblade.ca
disPosaL information
Please dispose of this product responsibly and recycle where possible.
conformity statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation, notwithstanding use by the
general public in commercial, business and industrial environments. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
3