Cleaning & Maintenance; Self-Cleaning - Black & Decker INCAPTO BXCO 1470e Mode D'emploi

♦ Remove the brewer (17) (Fig 5).
♦ Wash the brewer with fresh water. Dry the brewer afterwards.
♦ Take the opportunity to clean the surroundings of the brewer.
♦ Insert back the brewer (17) to its original position and install back the service door (16)
its original position.
Note: When Icon (D) lights up steady, it indicates that the brewer (17) is missing /
installed improperly. When Icon (D) is flashing, it indicates that the service door
(16) is missing/ installed improperly.
♦ Place the coffee grounds container (4) on the internal drip tray (3) and insert back into
it original position.
Note: When Icon (C) is flashing, the coffee grounds container (4) is missing.
♦ Place the external drip tray (1) at it original position.
CLEANING STEAM NOZZLE (5-6-7)
♦ Unlock the nozzle (6) by turning it to left (Sometimes you may need a pliers type tool,
but always without forcing it to avoid damaging it). Then pull it downward to remove
(Fig 6).
♦ Pull the metal tube (5) downward to dis-assemble the nozzle cover and metal tube (Fig 7).
♦ Wash the nozzle cover (6) with warm running water and use needle or bristle of brush
to clean the hole (Fig 8).
♦ Wash the metal tube (5) with warm running water and use needle or bristle of brush to
clean the hole (Fig 9).
♦ Replace the metal tube (5) back to the nozzle cover (6). Then push upward to place the
nozzle cover (7) back. And turn it to right to lock it (Fig 10).
Turning Off the machine
♦ Switch off the appliance by pressing the power on/off button (G).
Auto-Shut off
♦ The Appliance is equipped with auto-shut off. Depending on the mode you have selec-
ted the appliance will have different auto-shut off timing (See MODE SELECTION).
FURTHER SETTING
ADJUSTIING THE VOLUME OF YOUR COFFEE/HOT WATER
♦ You can memorize your desired volume of coffee for both strong coffee and mild coffee
and also the hot water from 25ml to 250ml.
♦ When making your coffee (either strong coffee (J) or mild coffee (K) or dispensing hot
water (I), press, release and immediately hold the button you selected. The appliance
will continue to make the cup of coffee.
♦ When the volume of coffee meets your desired volume, release the button. Two beep
sounds will be heard indicates that the volume of coffee is being memorized.
GRINDING ADJUSTMENT (Fig 11)
♦ You can adjust the grinder to suit the roast of your coffee by turning adjuster knob in
the bean container (Fig 11):
♦ To adjust the grind size, you can turn the adjustment knob, ALWAYS while the grinder
is grinding the coffee.
CAUTION: Never do the grinding adjustment when the grinder is not operating. It
may damage the grinder.
♦ The dots on the adjuster knob indicate the fineness of the grind
MODE SELECTION
♦ The machine has three different setting: default setting, ECO mode and speed mode.
In ECO mode, the appliance helps to save more energy. In speed mode, the user can
make their coffee faster than in default setting.
♦ Below you will see a chart with the active functions of each Mode.
ECO Mode
Illumination Light No
Pre-brewing* Yes
Auto shut off time 10mins
Speed Mode Default Setting
Yes Yes
No Yes
30mins 20mins
(Original instructions)
Cup Volume
Yes
memory
*Note: The pre-brewing function moistens the grounded beans in the brewer with
a small amount of water before full extraction. This expands the coffee grounds to
build up a greater pressure in the brewer which help extraction of all the oils and
full flavor from the grounded beans.
To select the desired MODE:
♦ When the machine is in standby condition, press and holds the ON/OFF Button (G) for
5 seconds, which will cause the J, K or L icons will begin to flash, depending on the
MODE the machine is in. Then release and pass to the next point
♦ The icons will blink according to the table below.
♦ To know which mode it is in, the table below indicates what is shown in the different
settings:
Hot water button
(I)
In ECO Mode Lights ON
In Speed Mode Flashing
In Default Setting Flashing
♦ To change the MODE, press the hot water button (I) for ECO mode, strong espresso
button (J) for speed mode and mild espresso button (K) for default setting.Two Beep
sound will be heard indicates that the mode is being selected. (Note: If you are pres-
sing the relative lights on button for each mode, the machine will not response).
♦ If you would like to remain the setting unchanged, press ON/OFF button (G again or
wait for 5 seconds for the machine to return to the standby condition.
CLEANING & MAINTENANCE

SELF-CLEANING

♦ When icon (E) light-up, it indicates that the appliance needs to undergo self-cleaning.
The appliance will remain in the best condition if this function is performed at least
once a month or more regularly depending on the hardness of water used. It is also
suggested:
♦ Fully fill the water tank (14).
♦ Adding one pack of cleaning agent included in the box to the water tank.
IMPORTANT: Do not use vinegar or other cleaning agent to do self-cleaning of this
appliance. The cleaning agent might damage the appliance.
♦ Plug in the appliance.
♦ Place a sufficient large container under the coffee spout.
♦ In standby condition, press and hold ON/OFF Button (G) and strong coffee button (J) at
same time, for 5 seconds. A beep sound will be heard with Icon (E) and strong coffee
button (J) will be flashing.
♦ Press strong coffee button (J) to confirm undergoing the self-cleaning process.
♦ Icon (E) will be flashing indicates that the appliance is undergoing the self-cleaning
process. To resume back to the standby condition, press ON/OFF button (G). (Caution:
Keep skin/body away from the hot water.)
♦ When all the water in the water tank is being dispensed out, Icon (A) (Low water level)
and strong coffee button (J) will be flashing. Remove all the remaining solution in the
water tank (14) and fill the tank with normal tap water until the MAX position. When wa-
ter is filled into the water tank, Icon (A) will goes off, then Strong Coffee (J) and Icon (E)
will be lighting up continuously. Then the appliance will continue the descaling process,
the appliance will brew half of water tank first and then waiting for around 1min, after
that will brew the outstanding water from the water tank.
♦ When the self-cleaning process is completed, the appliance will switch off automatica-
lly.
Note: To ensure the descaling process can be completed, please be patient during
the process and make sure the appliance switches off automatically
EMPTY SYSTEM FUNCTION
♦ The empty system function is recommended to be used before long period of non-use,
frost protection and before talking to repair agent.
♦ In standby condition, press and hold the ON/OFF button (G) and long coffee button (K)
together for 5 seconds, there will have two "Beep Beep" sound for indication.
♦ Empty System Icon (F) will then be flashing.
♦ Remove the water tank from the appliance. Icon (F) will light up stable indicating that
the empty system is under process. You can press ON/OFF Button (G) before remo-
ENGLISH
Yes Yes
Strong coffee Long coffee button
button (J)
(K)
Flashing Flashing
Lights ON Flashing
Flashing Lights On
11