Black & Decker INCAPTO BXCO 1470e Mode D'emploi page 10

ENGLISH
(Original instructions)
ACCESSORY
♦ In the box are included:
♦ Packs of cleaning agents for the process of self-cleaning.
♦ Cleaning cloth for Control panel.
♦ Cleaning brush.
MACHINE INSTALLATION
♦ Remove any protective films, stickers (in particular, the Control Panel protection
(10)) and any other packing material on the appliance.
♦ Choose a safe and stable surface with an easy to reach power supply and leave space
(minimum distance from each side) around the machine.
♦ Insert the external drip tray (1).It has magnets to facilitate assembly. Make sure it is
inserted correctly.
♦ Fill the water tank (14) with water (see "FILLING THE WATER TANK").
♦ Fill the bean box (11) with coffee bean (SEE "FILLING THE COFFEE BEAN CONTAI-
NER).
♦ Unwind and straighten the power cord and insert the plug into the socket located on
the back of the machine. Insert the other end of the power cord into a wall socket with
suitable power voltage.
Daily Operation
MAKING YOUR COFFEE
♦ Switch on the appliance by pressing the power on/off button (G).
♦ The appliance will rinse itself when turned on and when turned off and when it turns
itself off automatically. Place an empty container under the adjustable coffee spout
before turning on or off.
Priming: If for any reason you find some difficult for water to circulate,
proceed to prime the pump. To do this, simply press the hot
water icon (I) until a continuous stream of water comes out.
OPTION cancellation AUTOMATIC CLEANING:
As you can always do Cleaning Manually (see MANUAL RINSING), if you consider
the AutoClean option annoying, you can override that function as follows:
Open and remove the Service Door (16) (See Figs 2 and 3)
Press and hold the ON / OFF button for a few seconds until 2 beeps are heard.
That indicates that you have disabled self-cleaning
To reactivate it, repeat operation, until you hear the double beep
♦ The appliance is then in the standby condition.
♦ Place a cup under the coffee spout (9) and adjust the height of the spout the fit the cup.
Depending on the size of the cup (too tall or too wide) you can remove the drip tray (1)
or adjust the position of the drip tray as showed in (Fig 1).
♦ Depending on the taste of coffee you would like to have, press strong coffee button (J)
or long coffee button (K).
♦ The coffee button being pressed will light on and continue to be lit indicating that the
appliance is preparing the cup of coffee.
♦ While it is brewing, the cup lighting (13) will activate.
♦ When the appliance is back to standby condition, the coffee is ready to serve.
Tip: The strong coffee button (I), with higher coffee intensity,
is recommended for espresso coffee (both coffee buttons use approximately 9g
of coffee). The volumes of the coffee buttons (I, J) can be adjusted (see Section
OTHER CONFIGURATIONS / Volume of coffee and water).
Note: Press the hot water button (I) (see Section HOT WATER) to clean inside of
the coffee maker before first use.
FILLING THE WATER TANK
♦ When (A) Icon is flashing, the water tank (14) is in low water level and requires filling
the water tank.
♦ Lift the water tank (14) by using the lid as the handle.
♦ Rinse the water tank with fresh water and then fill the tank to the Max level and place it
back into the machine. Make sure it is fully inserted.
Note: To prevent spillage onto electrical parts, do not add water directly into the
appliance from another container.
IMPORTANT: Never fill the water tank with warm, hot, sparkling water or any other
liquid which might damage the water tank and the machine.
FILLING THE BEAN CONTAINER
♦ When (B) Icon is flashing, the appliance needs to be filled with coffee bean:
♦ Remove the bean container lid (12)
♦ Slowly pour in the coffee beans.
10
♦ Install back the container lid (12)
IMPORTANT: Fill the coffee bean container (11) with coffee beans only. Grounded
coffee, instant coffee, sugary roasted coffee and any other objects may damage
the machine.
PREPARING FROTHY MILK FOR COFFEE
♦ Since the temperature of steam is higher than the temperature of espresso, so coffee
should be prepared before making frothy milk; otherwise the espresso might be burnt.
♦ Prepare the coffee with large cup.
♦ Turn the steam nozzle toward (6) to the Drip tray (1).
♦ Press the steam button (H). Steam indicator light (8) will flash. Then the appliance is
heating up and draining the residual water into the Drip Tray or another container.
♦ After the steam indicator light (8) stop flashing and stay on, place a container with
milk under the steam nozzle and immerse the steam nozzle about 5 cm deep into the
container.
♦ Press the steam button (H) again.
♦ Swivel the container while the hot steam comes out.
♦ When the milk is hot enough with froth appeared. Then press again the steam button
to stop the steam.
♦ Use a wet towel to clean the nozzle cover and metal tube. (Refer to "DAILY CLEANING
OF THE APPLIANCE").
♦ Pour the hot frothy milk into the coffee.
♦ Now you can enjoy your coffee.
HOT WATER
♦ The appliance can dispense hot water by simply pressing the hot water button (I). The
hot water button (I) and the illumination (8) will lights up indicates that the appliance is
heating up the water. When the hot water button and the illumination turn off, the water
is ready to serve. You can always stop when you have enough.
FAVOURITE FUNCTION
♦ You can use the Favorite function to memorize an additional volume selection for soft
coffee, strong coffee or Hot Water (Additional to only one of the three).
Set up the Favorite coffee setting
a) Press and hold the Favorite button (L) for 2 second, then the mild coffee (K),
strong coffee (J), and hot water button (I) will flash and you can select any one to
memorize the volume.
b) When you select either strong espresso, mild espresso or hot water. You will
see the drinks come out, and then you can press and immediately hold to keep
dispensing the drinks and stop it by release the button. After that the volume will be
memorized.
Using the Favorite function
♦ Once the Favorite function is programmed, just press the Favorite Function button (L),
and the memorized drink will come out.
DAILY CLEANING OF THE APPLIANCE
♦ Timely cleaning and maintenance of the appliance is very important in prolonging the
life of the appliance.
CLEANING BREWING UNIT (17)
♦ Remove the external drip tray (1).
♦ Empty the water inside the drip tray in the sink and wash it with fresh water. Dry it
afterwards.
♦ Slides open the internal drip tray (3) and the coffee grounds container (4).
♦ Empty the coffee grounds container and wash it with fresh water. Dry it afterwards.
ATTENTION: Never remove the coffee grounds container (4) to empty it with the machi-
ne at half cycle. That could happen when you run out of water in the middle of making
coffee. The machine is halfway through, waiting for to refill the tank to finish the cycle
automatically. In that case, you will not be able to take it (4) out. Never force to remove
it because it could damage some component. If you do it, it will cost you a lot to put the
complete set back in its place. The machine will not work because it does not detect the
drawer (4). You only will be able to put it without the internal drip tray (3). Once the water
tank is filled and the drawer (4) has been placed without (3), the machine will continue
with the interrupted cycle. Then you can return the set (3) + (4) and the machine will be
ready to operate again
Note: When the icon (C) lights up, the coffee grounds container needs to be empty.
♦ Pull down the service door (Fig 2).
♦ Remove the service door (16) (Fig 3).
♦ Press the release (Orange) knobs of Brewing group (17) (Fig 4).