Technical Data; Description Of The Unit; Functional Principle; Unpacking The Unit - Air-O-Swiss E2441 Mode D'emploi

Technical data

Technical data
Value
Electrical voltage
Power consumption
Humidity output
Suitable for rooms
Water capacity
Dimensions LxWxH 320 x 320 x 400 mm
Weight (empty)
Operation noise level

Description of the unit

Description of the unit
The unit consists of the following components:
• B 1 B 1 F illing opening
• B 2 B 2 T op assembly
B 3 B 3
• F loat assembly (B 16–19)
B 4 B 4
• I onic Silver Stick (ISS)
®
• B 5 B 5 W ater base (B 5–7)
• B 6 B 6 W ater capacity fill line
B 7 B 7
• B ase handles
B 8 B 8
• S pout
B 9 B 9
• L ifecycle indicator for the Ionic Silver
Stick (ISS)
®
• B 10 B 10 P ower cord/plug
• B 11 B 11 B ase (B 11–14)
B 12 B 12
• F an
B 13 B 13
• S lide switch (B 20–21)
• B 14 B 14 P ower rating plate (on the underside of
the unit)
The float assembly consists of the following parts:
B 15 B 15
• F loat tip
B 16 B 16
• W ater level indicator ring (max. 3.8 l)
• B 17 B 17 E vaporator wick A7018
• B 18 B 18 F loat basket
B 19 B 19
• F loat body (styrofoam)
The slide switch consists of the following parts:
• B 20 B 20 S lide switch
B 21 B 21
• O perating light
Operating modes
The following operating modes can be set on the
slide switch:
Position Function
0 The unit is switched off
I The unit is operating in night mode
(low noise level)
The operating light turns green
II The unit is operating in normal mode
(maximum humidity output)
The operating light turns green
Operating light
The operating light illuminates green as soon as the
unit is switched on. If the water base is taken off
230 V / 50 Hz
the base, the green LED changes to red and unit
20 W
operation is interrupted, but the unit is not current-
up to 220 g/h
less. Only when the water base is returned to the
base does the red LED turn green again and the unit
up to 40 m²
resumes operation.
max. 3.8 l
min. 0.2 l Power rating plate
B 14 B 14 The following information is displayed on
3.8 kg
the power rating plate:
< 25 dB(A)
• Product name
• Electrical voltage
• Power consumption
• Protection class
• Production number
• Production date
• The data on the power rating plate in the illustra-
tions is only exemplary. Please check the data on
the power rating plate of your unit.

Functional principle

Functional principle
When filling the unit, the float switch is lifted with
the water gauge. When the water gauge reaches the
water capacity fill line, the float tip closes the fill-
ing opening of the unit. The evaporator wick soaks
up water. The fan pushes the dry room air through
the moist mat and emits it as sufficiently moistur-
ized air. Through the directed guiding of the airflow,
nearly constant humidification is possible at every
water level. Therefore the unit creates optimum
air moisture, without additional control units being
necessary.
Ionic Silver Stick
nance
B 4 B 4 The specially adapted anti-microbial protec-
tion system Ionic Silver Stick
growth in the water in the water base. Therefore no
chemical additives are necessary for water quality
maintenance.
The Ionic Silver Stick
and can be used for a year.
Lifecycle indicator
B 9 B 9 The unit is equipped with a lifecycle indica-
tor for the Ionic Silver Stick
current month on the label and write the current
year on the line provided.

Unpacking the unit

Unpacking the unit
At delivery the unit is completely assembled and
already equipped with an evaporator wick.
The float body (styrofoam) is a component of
the float assembly and does not belong to the
packaging.
for water quality mainte-
®
prevents microbial
®
is self-renewing, service free
®
® . Please cross off the
CAUTION
Risk of injury by falling parts!
▶
Always handle the unit by the base when un-
packing and lifting.
CAUTION
Damage to the unit due to removal of the float
body (styrofoam)!
▶
Do not remove the float body (styrofoam) when
unpacking the unit.
1. Open the packaging.
2. C 1 C 1 Remove the upper part of the styrofoam
packaging.
3. C 2 C 2 Reach into the filling opening and grasp
the upper end of the plastic bag securely.
4. C 3 C 3 Carefully pull the plastic bag with the unit
out of the packaging. When doing so, grasp the
plastic bag securely and do not let go of the plas-
tic bag when removing.
5. C 5 C 5 Place the plastic bag with the unit on the
floor and push the plastic bag down along the
unit.
6. C 6 C 6 Hold the unit by the base and lift up out of
the plastic bag.
➥
All packaging components as well as the plastic
bag are removed from the unit.
7. B 14 B 14 Check data regarding the power supply
on the power rating plate.
8. B B Check that all components of the unit are
included.

Putting the unit into operation

Putting the unit into operation
Positioning the unit
CAUTION
Damage to the plastic due to high tempera-
tures!
▶
Do not expose the unit to temperatures > 50 °C.
Observe the following pointers when positioning the
unit:
• A 14 A 14 Remember to ensure easy accessibility
and sufficient room for servicing and cleaning
the unit.
• Only operate the unit when it is filled!
1. Place the unit on the floor or on a flat, dry surface
in the room.
2. Fill the unit (see chapter "Filling the unit").
Filling the unit
There are the following possibilities for filling the
unit with water:
• using the filling opening on the upper part or
• directly into the removed water base from a fau-
cet.
✔
There are no foreign objects in the unit.
✔
B B The unit is assembled properly.
9