Table des Matières
Publicité
Les langues disponibles
Les langues disponibles
Guidelines for extension cord use
Extension cords are only to be used for temporary purposes. They do not replace the
need for installation of outlets and proper wiring where necessary.
In the shop and on construction sites:
1. Extension cords with an equipment grounding conductor must be used at all times.
2. Extension cords must be protected from damage, and not run through doorways
or windows where the doors or windows can close, causing damage to the cord.
3. Extension cords must be a minimum of 16 AWG and be rated for the equipment
in use.
4. Extension cords must be periodically inspected to ensure that the insulation and
conductivity of the wires are not compromised.
5. Extension cords should not be run through water or allowed to have connections
that may be exposed to accumulated water.
TABLE 1
Nameplate
Amperes
25'
@120 V
0 -5
16
5.1 - 8
16
8.1 -12
14
12.1 - 16
12
NR – Not Recommended
ELECTRICAL SHOCK HAZARD
The metal parts of this product conduct electricity. Avoid any condition that causes
electrical contact. Improperly grounded power tools present a hazard of electrical shock
that can result in serious bodily injury or death, particularly when used in a damp location,
in proximity to plumbing and other earthed surfaces, or outdoors.
WARNING:
Dust created by sanding, sawing, grinding, drilling, and other
construction activities may contain chemicals known to the State of California to cause
cancer and birth defects or other reproductive harm. Examples of these chemicals are:
a) Lead from lead-based paints
b) Crystalline silica from bricks and cement and other masonry products
c) Arsenic and chromium from chemically treated lumber
Your risk from exposure to these chemicals depends on how often you do this type of
work. To reduce your exposure, work in a well-ventilated area with approved safety
equipment, such as a dust mask specifically designed to filter out microscopic particles.
WARNING:
This product can expose you to chemicals including
Carbon 1333-86-4, which are known to the State of California to cause cancer.
For more information go to www.P65Warnings.ca.gov.
Kreg Tool Company warrants to the original purchaser only, that the Kreg
Mobile Project Center will be free from defects in material and workmanship
for a period of three (3) years from date of purchase. Kreg Tool Company
will, at its option, repair or replace any product (or component part thereof)
proving defective during said warranty period. This warranty applies only
to products which are used in accordance with all instructions set forth in
catalogs, manuals and/or instruction sets furnished by Kreg Tool Company.
This warranty becomes effective only if the original purchaser fully and
properly completes product registration online (www.kregtool.com) or calls
Kreg Tool Company Customer Service (1-800-447-8638).
This warranty is null and void if the product has been subjected to (1)
misuse, abuse or improper storage; (2) accident, neglect, damage or other
circumstances beyond Kreg Tool Company's control; (3) modifications,
disassembly, tampering, alterations or repairs not authorized by Kreg Tool
Company; and (4) for non-original purchasers. This warranty does not apply
to normal wear and tear, corrosion, abrasion, or repairs required due to
natural causes or acts of God.
General Safety Instructions
Extension Cord Length
50'
75'
100'
150'
Recommended Wire Gauge
16
16
14
12
16
14
12
10
14
12
10
NR
12
NR
NR
NR
Kreg Mobile Project Center Limited Warranty
Explanation of safety symbols found on the
Do not apply unbalanced loads.
Do not stand on the Mobile Project Center.
Do not sit on the Mobile Project Center.
200'
Do not stand on shelf.
12
NR
NR
NR
Always wear eye protection.
Maximum load, both table tops deployed: 350 lbs.
[158 kg.] uniformly distributed; 100 lbs. [45 kg.]
uniformly distributed on either table wing
Maximum load, two Mobile Project Centers,
table tops not deployed: 2200 lbs. [997 kg.]
Maximum load on shelf: 25 lbs. [11 kg.]
This is Kreg Tool Company's sole warranty. Any and all other warranties
which may be implied by law, including any warranties for merchantability
or fitness for a particular purpose, are hereby limited to the duration of this
warranty. Kreg Tool Company shall not be liable for any loss, damage or
expense directly or indirectly related to the use of its products or from any
other cause or for consequential damages (including without limitation, loss
of time, inconvenience, and loss of production). The warranty contained
herein may not be modified and no other warranty, expressed or implied,
shall be made by or on behalf of Kreg Tool Company.
For your records the following information will be useful in the event a
warranty claim is required. For complete records attach copy of proof of
purchase.
Date of Purchase ___/___/___
Purchased From:____________________________________________
Mobile Project Center
Publicité
Table des Matières
